699608
9
Zoom out
Zoom in
Previous page
1/15
Next page
CA-4v1 SATEL 7
The access code 4 can be used once only (the panel clears it after one-time entry).
The access codes 2, 3 and 4 can be cleared by pressing the [#] key immediately after
activating the service programming mode.
Bypassing zones (function 5)
Enter one of the two master codes and press the [
*
] key. The panel will confirm the
correct code entry with two short beeps and will wait for the function number entry (the
[TROUBLE], [ARMED] and [ALARM] LEDs will blink simultaneously). Press
the 5 key (the panel will confirm the entry with three short beeps, the [TROUBLE],
[ARMED] and [ALARM] LEDs will blink in turns). Zone numbers to be bypassed
should be entered. While programming the LEDs representing the bypassed zones will
be on. After setting the bypass function for the selected zones the [#] key should be
pressed.
Caution: the panel will signal an error if bypassing the 24-hour zone is attempted.
Reviewing the alarm memory log (function 6)
Enter one of the two master access codes and press the [
*
] key. The panel will confirm
the correct code entry with two beeps and will wait for the function number entry (the
[TROUBLE], [ARMED] and [ALARM] LEDs will blink simultaneously). The 6 key
should be pressed. The [ALARM] LED will start blinking, and the remaining LEDs will
indicate the origin of the last alarm (the [ARMED] LED will indicate the alarm
activated by entering three incorrect access codes, the [TROUBLE] LED will indicate
PANIC type alarm). Pressing any of the keys (except [
*
]) will classify the previous alarm.
The panel logs the last three instances of alarm condition. Pressing of the [
*
] key exits
the function.
Identifying trouble type (function 7)
If the [TROUBLE] LED is on, the panel detected a trouble condition. The type of
trouble is indicated after choosing function 7. In order to do that enter one of the two
master codes and press the [
*
] key. The panel will confirm the correct code entry with
two beeps and will wait for the function number entry (the [TROUBLE],
[ARMED] and [ALARM] LEDs will blink simultaneously). Press the 7 key. The
[TROUBLE] LED will start blinking, and the remaining LEDs will indicate the type of
trouble.
LED 1 detector power supply fuse (F1) trouble,
LED 2 output OUT1 fuse (F2) trouble or disconnecting the signaling device
attached to OUT1 output,
LED 3 output OUT2 fuse (F3) trouble or disconnecting the signaling device
attached to OUT1 output,
LED 4 battery fuse (F4) trouble or low battery,
[ALARM] LED no AC power supply.
Caution: the function can be used only when the [TROUBLE] LED is on.
Setting the ADDITIONAL FUNCTIONS (function 8)
Enter one of the two master codes and press the [
*
] key. The panel will confirm the
correct code entry with two beeps and will wait for the function number entry (the the
[TROUBLE], [ARMED] and [ALARM] LEDs will blink simultaneously). Press the
8 key. The panel will signal programming mode activation with three short beeps, the
[TROUBLE], [ARMED] and [ALARM] LEDs will blink in turns and the 1÷4
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-4v1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-4v1 in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info