699608
8
Zoom out
Zoom in
Previous page
1/15
Next page
6 SATEL CA-4v1
TROUBLE (yellow color) – blinking LED indicates a failure in the alarm system The
type of trouble can be identified with function 7.
14
(red color) LEDs indicating the status of system zones:
ON – zone violated,
blinking slowly – zone bypassed (indicated only with the partition disarmed).
The jumper pins on the keypad board are designated for setting a keyboard backlighting.
Basic functions
Arming
Enter one of the access codes (except the servicing code) and then press the [#] key.
The panel will confirm the correct code entry with three short beeps and will start to
countdown the exit delay time. During the countdown the [ARMED] LED is blinking,
and after armed mode is activated it is lit continuously.
Disarming
Enter one of the access codes (except the servicing one) and then press the [#] or [
*
]
key. The panel will confirm the correct code entry with three short beeps and the armed
mode will be deactivated. The [ARMED] LED will extinguish.
Canceling the alarm
Is similar to disarming the system. If the alarm was activated in armed mode along with
canceling the alarm the armed mode is deactivated.
PANIC alarm
Press and hold the [#] key for about 3 seconds. The function can be blocked (see
ADDITIONAL FUNCTIONS)
Access code programming (functions 1, 2, 3, 4)
The default user first access code is 1234. The code should be changed for a safety
reasons with function 1 right after starting the system.
To changing or programming code enter one of the two master access codes and press
the [
*
] key. The panel will confirm the correct code entry with two short beeps and will
wait for the number of the access code to be programmed. In addition, the
[TROUBLE], [ARMED] and [ALARM] LEDs will blink simultaneously. Giving the
number (1 through 4) will activate the programming mode. The panel will confirm the
programming mode with three short beeps. The [TROUBLE], [ARMED] and
[ALARM] LEDs will blink in turns. A new access code should be entered and confirmed
with the [#] key. The access code should be 4 to 6 digits long.
The access codes 1 and 2 are master codes.
The access code number 3 is designed to enable arming the system with bypassing the
zones programmed with function 9 and armed mode without outside signaling devices
activated (the alarm condition is signaled solely in the keypad, the option is deactivated
with function 8).
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-4v1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-4v1 in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info