699577
51
Zoom out
Zoom in
Previous page
1/60
Next page
SATEL CA-10 49
If this option is inactive, violation of a zone when the partition is armed will generate an
alarm, provided the keypad is not already signaling a previous alarm. If the keypad is already
signaling an alarm, violation of the zone will not cause a new alarm.
FS132 - programming of clock correction (DEC)
As time measurement by the control panel internal clock may differ from the real value,
provision has been made for making a daily time correction. The function makes it possible
to correct the time measurement by ±19 seconds within 24 hours. For programming the time
correction, use the function FS132 to enter the value of daily time shift of internal clock:
In the LED keypads, the programming consists in entering two digits, depending on the
expected correction value (see table below).
Correction value[s] -19 -18 -17 ... -2 -1 0 1 2 ... 17 18 19
Programming 99 98 97 ... 82 81 00 01 02 ... 17 18 19
EXAMPLE:
program the time correction by -12 seconds
[1][3][2] [#] - call the function
[9][2] [#] - enter the correction value (minus 12 seconds)
In the LCD keypads, the correction is programmed by means of the arrow keys: the key
enters a negative correction, the key - a positive one.
Monitoring - programming system report codes
FS133 - programming the time of test transmission to the monitoring station (DEC)
The alarm system makes it possible to set a maximum time interval between transmissions
of events codes. If the preset time interval elapses after the last monitored event, the control
panel will send the test transmission code. The function parameter (three two-digit numbers
meaning days, hours and minutes) determines the time counted from the last transmission. If
any event, the code of which will be sent, occurs in the system, the control panel will start
counting the time again. This feature can be disabled by programming 00,00,00.
EXAMPLE (for LED keypad):
programming of the test code send after two and a half hours since the last transmission
(communication test).
[1][3][3] [#] - calling the function,
[0][0] - entering the number of days (the LED 12 is blinking),
[#] - confirming the parameter,
[0][2] - entering the number of hours (the LED 11 is blinking),
[#] - confirming the parameter,
[3][0] - entering the number of minutes (the LEDs 11 and 11 are blinking),
[#] - confirming the parameter and leaving the function.
Note: Only a 3 successive events of the test transmission are saved in the control panel
memory, all the rest is not saved though the test transmissions are conducted. After
a new event occurs, the next 3 test transmission events can be saved.
Monitoring – programming zone report codes
FS134 - programming codes to bypass the control panel zones (HEX)
The codes programmed with this function are sent after calling the user function 4 and
bypassing the control panel zones. The codes are programmed in the same way as the other
zone events codes (FS60 – FS66).
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 Installation Guide - English - 43 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info