699577
59
Zoom out
Zoom in
Previous page
1/60
Next page
SATEL CA-10 57
Restoring default settings, restoring codes
Restoration of settings on entering the service mode by means of service
code
If it is necessary to restore the default settings, you should enter the service mode and call the
service functions FS107 (to restore all the default settings, except for the user access codes)
and FS110 (to restore the partition master default codes, the other codes being erased). Also,
the function FS108 can be performed (in order to erase the event log contents).
Restoration of settings on entering the service mode by hardware means
If the service mode is inaccessible (for example, when the control panel stopped responding to
keypad commands because of a programming error, or the service code has been lost), to
restore default settings follow the procedure below:
1. Disconnect in turn the mains supply and the emergency supply.
2. Set a jumper on J19 RESET pins.
3. Connect in turn the emergency supply and the mains supply.
4. On hearing a beep in the keypad, remove the jumper from J19 pins (the 1
st
partition keypad will enter the service mode).
5. Perform function FS107 (restoring of default settings).
6. Perform function FS110 (restoring of default codes).
7. Exit the service mode or proceed with programming the control panel.
This procedure can be disabled by software means (see: FS131 first option in the first set of
option).
Note: Similarly as in other SATEL control panels, shorting the pins and powering up alone will
not restore any parameters. However, it will activate the service mode thus making it
possible to check how the control panel has been programmed, and to analyze any
programming errors.
Restoration of settings when the option to enter the service mode by
hardware means is locked and it is impossible to use the service code
If the option to enter the service mode by jumper setting is disabled (FS131 first option in the
first set of option) and the panel does not recognize the service code, proceed as follows:
1. Disconnect in turn the mains supply and the emergency supply.
2. Set a jumper on J19 RESET pins.
3. Connect in turn the emergency supply and the mains supply.
4. Wait about 60 seconds (±5 sec.) and remove the jumper.
5. Enter from keypad the code: [1][2][3][4][5] (the code should be entered within 15
seconds) and confirm by pressing the [#] or [
*
] key.
After these operations, the control panel should return to its default settings and remain in the
service mode.
59


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 Installation Guide - English - 43 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info