699577
47
Zoom out
Zoom in
Previous page
1/60
Next page
SATEL CA-10 45
parameters of the system to which the panel transmits its messages. If parameters of such
signals change, it will be sufficient to specify new data.
In the LED keypads the programming consists in entering six two-character codes which are
suitable for the given paging system.
Messaging – programming of HEX messages
FS119 - programming message 1 (HEX)
FS120 - programming message 2 (HEX)
FS121 - programming message 3 (HEX)
FS122 - programming message 4 (HEX)
The functions FS119 – FS120 permits programming an alphanumeric message for any
paging system. The programming consists in entering up to 84 message characters (in the
LED keypads in two-character pairs), in a convention required by the given system.
Some systems require additional characters:
A - #
B -
*
C - end of message
E - pause (required in some systems to separate the pager number from the
message)
D and F - same as C.
Note: The functions FS119 - FS122 are an alternative to the functions FS96 - FS99. Each
message can be programmed in two ways (in the HEX mode or in the POLPAGER
receiver convention).
Functions programming basic options
FS123- counters count-up times
The function makes it possible to program time intervals related to the counters 1, 2 and 3 of
counting zones (see: FS7). The alarm will only be generated when the number of violations
preset in FS7 takes place within the time interval defined by the function FS123. The count-
up times may be programmed within the interval from 1 to 255 seconds (by default set at 30
seconds). If the number of violations programmed in the function FS7 does not take place
within the time interval defined in the function, after expiry of the time the counting zone
counters will be reset.
Programming of the counters count-up times consists in entering a number from the range of
1 to 255 for each counter.
In the LED type keypads, after starting the function, you should enter one, two or three digits
for the first counter. Upon confirmation with the key [#], the control panel proceeds to
programming the count-up time of the next counter. In the course of programming, the LEDs
9-12 indicate in binary form which counter the parameter refers to. On the LEDs 1-8, the
control panel displays the previously programmed setting of the parameter in the binary
form. The programming can be terminated by pressing the key [
*
].
EXAMPLE
changing the counter count-up time: the first to 60 seconds, the second to 150 seconds, the
third to 255 seconds
[1][2][3] [#] - call the function
[6][0] - enter the count-up time for counter 1 (LED 12 is blinking during programming)
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 Installation Guide - English - 43 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info