699577
39
Zoom out
Zoom in
Previous page
1/60
Next page
SATEL CA-10 37
Notes:
The code 3 is recorded in the event log when the control panel is unable to establish
communication with the station. In that case, the control panel will retry after 120
seconds to establish connection. When it gets through, the control panel will transmit all
events from the memory. The "transmission problems" code item makes it possible to
asses when the oldest event occurred. The events are sent by the panel in the order of
their occurrence (the oldest event is sent first), unless the event sorting mode is active.
In such a case, the zone events are sent first, then the partition events, and the system
events are sent last.
The code 4 is recorded in the event log when lack of communication with the station
lasted so long that all the memory intended for the events (255 in all) has been filled up
and the oldest events have been erased.
FS83 - programming system event assignment to station 1 (BIT)
When the mode of notifying both stations is active, the events programmed with the function
FS82 are sent to both stations. For the other system events (programmed with the function
FS81), it is possible to determine, whether they will be sent to station 1, to station 2, or to
both of them. The function FS83 selects events to be sent to station 1.
Programming in the LED keypad is a two-stage process.
In the firs stage the LEDs 1 to 8 show the following events:
1 - AC loss
2 - AC restore
3 - Low battery
4 - Battery restore
5 - Output OUT1 trouble
6 - Output OUT1 restore
7 - Output OUT2 trouble
8 - Output OUT2 restore
In the second stage the LEDs 1 to 8 show the following events:
1 - Output OUT3 trouble
2 - Output OUT3 restore
3 - Printer trouble
4 - Printer restore
5 - Enter service mode
6 - Exit service mode
7 - Start DOWNLOADING
8 - End DOWNLOADING
FS84 - programming system event assignment to station 2 (BIT)
The function makes it possible to select system events sent to the station 2, when the mode
of reporting to both stations is active. The programming procedure is identical as in FS83.
FS85 - programming test transmission time (DEC)
The control panel can send the test transmission every 24 hours. The function FS85 sets the
hour and minute for sending the test code to the monitoring station. The programming
consists in entering two two-digit numbers: hours (00 to 23) and minutes (00 to 59). After
confirmation of the minutes, the panel quits the function. Entering 99:99 disables the test
transmission function.
EXAMPLE (for LED keypad):
programming the test code to be sent at 1:45
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 Installation Guide - English - 43 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info