699577
19
Zoom out
Zoom in
Previous page
1/60
Next page
SATEL CA-10 17
Note: Options 7 and 8 of the third set are only relevant with activated option 7 of the second
set – „outputs OUT5, OUT6 control NOKTON radio messaging”.
FS6 - programming the global times (DEC)
The settings refer to the entry delay, exit delay and alarm time. The times are valid for the
entries and exits to which no individual times are assigned. The exit delay time is common
for all partitions. The alarm time programmed in this function refers also to the keypad
alarm signaling.
Note: The alarm time set with the function FS6 defines also the zone alarms cut-off time -
when the alarm is on, the subsequent zone violations will not trigger consecutive
alarms until the cut-off time has elapsed.
The time values are programmed within the range from 1 to 99 seconds.
In the LED type keypads, the values of entry time, exit time and alarm time are entered in
turn by two digits.
EXAMPLE (for the LED keypad):
programming the times: entry delay=30s, exit delay=60s, alarm=90s
[6] [#] - call the required function
[3][0] [#] - enter the entry delay time (two digits) – the LED 12 is blinking
[6][0] [#] - enter the exit delay time (two digits) – LED 11 is blinking
[9][0] [#] - enter the alarm time - the LEDs 11,12 are blinking - after acknowledging the last time, the
control panel automatically exits the function.
When programming from the LCD keypad, pressing the [#] key confirms all the three times
entered.
FS7 - programming the counting zone counters (DEC)
The control panel is equipped with three independent violation counters which can be
associated with any zones. Violation of these zones will trigger alarm after the programmed
number of violations is exceeded in the respective zone counter. Each counter can sum up
violations of one or several zones defined as the counting ones (e.g. the counter 1 can count
violations of zone 2, the counter 2 - violations of zones 4, 5, 6). The alarm will be generated
by the zone which has been violated as the last one.
Three counter values are programmed, from 01 to 07, in the following order: counter 1,
counter 2, counter 3. If no counting zones are provided in the panel, the programmed values
are irrelevant.
- Number „0” programmed – alarm after 8 violations.
- Number „1” programmed – alarm after the second violation.
- Number „2” or higher programmed – alarm after the number of violations equal to the
value programmed.
Time gates corresponding to the counters are programmed in FS123.
EXAMPLE (for LED keypad):
programming the counters: the 1
st
- 2 violations, the 2
nd
- 5 violations, the 3
rd
- not used
[7] [#] - call the function
[0][2] [#] - program the first counter (the lower LED B is blinking)
[0][5] [#] - program the second counter (the lower LED A is blinking)
[
*
] - exit the function - programming of the third counter is omitted
Functions programming partition assignment
FS8 - zones assignment to partition 1 (BIT)
FS9 - zones assignment to partition 2 (BIT)
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 Installation Guide - English - 43 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info