699577
7
Zoom out
Zoom in
Previous page
1/43
Next page
CA-10 Installer Manual 5
the source). It is also possible to indicate (in the output options) the partition the output is associated
with. If this is the case, the zone alarms will be limited to those from the zones belonging to the
partition indicated. When the "list of outputs" is empty and no partitions are indicated, the output reacts
to all alarms (except for the fire alarms).
The output can remain active for a specified time (from 01 to 99 seconds or from 01 to 99 minutes) or
until the alarm is cleared by the user. During its operation, it can every second change its state
(pulsate).
2 fire/burglary alarm the output starts on detecting by the control panel of a burglary alarm
(continuous signal) and/or a fire alarm (intermittent signal). The output operation can be limited to the
indicated "list of outputs" or a specific partition (identically as for the 1 output type). The output can
remain active for a specified time (from 01 to 99 seconds or from 01 to 99 minutes) or until the alarm is
cleared by the user.
3 fire alarm the output starts when the control panel detects a fire alarm. Such an alarm is triggered by
fire zones or the user (through the FIRE ALARM function). The output operation can be limited to the
specified "list of outputs" or particular partitions (identically as for the 1 output type), indication of any
zones other than the fire ones having no sense, as they would not generate a fire alarm. The output
can remain active for a specified time (from 01 to 99 seconds or from 01 to 99 minutes) or until the
alarm is cleared by the user. During operation, it can every second change its state (pulsate).
4 keypad alarm the output starts on detecting any keypad alarm (FIRE, PANIC, AUX., keypad tamper
alarms). The output operation can be limited to the alarms from specified partitions. The output can
remain active for a specified time (from 01 to 99 seconds or from 01 to 99 minutes) or until the alarm is
cleared by the user. During its operation, it can every second change its state (pulsate).
5 keypad fire alarm the output starts on triggering the fire alarm by the user (with the FIRE ALARM
function). The output operation can be limited to the alarms from specified partitions. The output can
remain active for a specified time (from 01 to 99 seconds or from 01 to 99 minutes) or until the alarm is
cleared by the user. During operation, it can every second change its state (pulsate).
6 keypad panic alarm the output starts on triggering the PANIC alarm by the user. The output
operation can be limited to the alarms from specified partitions. The output can remain active for a
specified time (from 01 to 99 seconds or from 01 to 99 minutes) or until the alarm is cleared by the
user. During operation, it can every second change its state (pulsate).
7 keypad aux. alarm the output starts on triggering the alarm by the user with the ALARM AUX
function. The output operation can be limited to the alarms from specified partitions. The output can
remain active for a specified time (from 01 to 99 seconds or from 01 to 99 minutes) or until the alarm is
cleared by the user. During operation, it can every second change its state (pulsate).
8 keypad tamper alarm the output starts on detecting violation of the tamper contact or a change of
the keypad address, and also after 3 wrong codes. The output operation can be limited to the alarms
from specified partitions. The output can remain active for a specified time (from 01 to 99 seconds or
from 01 to 99 minutes) or until the alarm is cleared by the user. During operation, it can every second
change its state (pulsate).
9 day/night + counting the output starts on detecting violation of disarmed DAY/NIGHT zone or
violations of COUNTING zones, which trigger no alarm. Operation of the output can be restricted to
a specified “list of outputs” or particular partitions (identically as for the 1 output type). Indication of any
other zones than those tested by this output type is irrelevant they will give no violation signal. The
output can remain active for a specified time (from 01 to 99 seconds or from 01 to 99 minutes) or until
the alarm is cleared by the user. During operation, it can every second change its state (pulsate).
10 duress alarm the output starts on using an access code with authority level 4 (DURESS) to disarm
the system or to signal an alarm. This code is used to trigger a special "disarm under duress" alarm.
Operation of the output can be restricted to alarms from particular partitions. The output can remain
active for a specified time (from 01 to 99 seconds or from 01 to 99 minutes) or until the alarm is
cleared by the user. During operation, it can every second change its state (pulsate).
11 chime the output starts on violating the disarmed zones for which the “chime” option has been
activated. Operation of the output can be restricted to the indicated "list of zones" or to specified
partitions (identically as for the 1 output type). The output can remain active for a specified time (from
01 to 99 seconds or from 01 to 99 minutes) or until the alarm is cleared by the user. The output signals
violations irrespective of the chime lock setting in keypad (the lock is called by holding down the [8]
key).
12 switch MONO the output is activated by calling the user function 7 ([CODE][
*
][7]) or using a code
with authority level 5 ([CODE][#]). Operation of the output can be restricted to specified partitions.
The output can remain active for a time from 01 to 99 seconds or from 01 to 99 minutes.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 60 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info