699577
5
Zoom out
Zoom in
Previous page
1/43
Next page
CA-10 Installer Manual 3
EOL, 2EOL/NC, 2EOL/NO. The use of 2EOL configuration enables the panel to
simultaneously control the detector and its tamper circuit by means of one pair of wires.
The zones can perform the following functions in the system:
0 entry/exit the violation of which, when in the armed mode, will start countdown of the entry delay
time and will enable the delay mechanism for INTERIOR DELAY type zones (violation of an
INTERIOR DELAY zone without prior violation of the ENTRY/EXIT zone will trigger an alarm
immediately). Upon violation, a “zone violation” code is sent to the report station (it is possible to skip
sending this message), and, after counting down the "entry delay time" and triggering the alarm
- a “zone alarm” code. The "entry delay" countdown can be signaled in the keypad. It is possible to
define automatically bypassing zones if no ENTRY/EXIT zone is violated during the exit delay time”.
Because of its additional functions, this zone type cannot be used as a common zone for several
partitions.
1 delay when violated in the armed mode, it starts delay countdown, after which an alarm is triggered.
It will not occur if the zone is disarmed before completion of the delay countdown. Upon violation,
a “zone violation” code is sent to the report station (it is possible to skip sending this message), and,
after counting down the "entry delay time" and triggering the alarm – a “zone alarm” code. The delay is
not signaled in the keypads.
2 interior delay when violated in the armed mode after previous violation of the ENTRY/EXIT zone, it
behaves like a DELAY zone. When violated in the armed mode without previous violation of the
ENTRY/EXIT zone, it behaves like an INSTANT zone.
3 instant when violated in the armed mode, it immediately triggers an alarm and sends a ”zone alarm”
message to the monitoring station.
4 day/night when violated in the armed mode, it behaves like an INSTANT zone, while when
disarmed, it will signal violation in the keypad (unless the signaling is disabled) and send a “zone
violation” code to the station.
5 counting L1 when violated in the armed mode, it increases the status of the first of three violation
counters (a „zone violation” code is sent to the station), until the number of violations specified for that
counter is exceeded (programming in FS7). Then, the violation triggers an alarm (a „zone alarm” code
is sent to the report station). The violation counter is reset after 30 seconds since the first violation.
It is possible to program another counter count-up time (FS123). If the preset number of violations is
not reached within this time, there will be no alarm. More than one zone can be define as “counting L1”.
Violations of those zones will be summed up. Violation of the counting zone in armed mode can be
signaled in the keypad in the same way as for the DAY/NIGHT zone.
6 counting L2operation identical as for the "counting L1", but changes the status of the second of the
three counters.
7 counting L3 operation identical as for the "counting L1", but changes the status of the third of the
three counters.
8 24H audible armed all the time, irrespective of whether the partition it is assigned to is armed, or not.
Each violation of this zone will trigger alarm on the BURGLARY ALARM type outputs, in the keypad, and
will send a “zone alarm” code. It makes possible to create tamper circuits and panic buttons.
9 24H auxiliary armed all the time, irrespective of whether the partition it is assigned to is armed, or
not. Each violation of this zone will trigger an alarm in the keypad and will send a “zone alarm” code. It is
intended for connecting detectors not related to the burglary alarm, such as gas or flooding sensors, etc.
10 24H silent armed all the time, irrespective of whether the partition it is assigned to is armed, or not.
Violation of this zone will only send a “zone alarm” code to the monitoring station.
11 24H fire armed all the time, irrespective of whether the partition it is assigned to is armed, or not;
intended to manage the fire detectors.
If the control panel contains an output programmed as the FIRE DETECTORS POWER SUPPLY,
violation of the zone will actuate the alarm verification mechanism and will signal alarm in the keypad.
To perform the verification, disconnect momentarily power supply to the fire detectors and check,
whether after reconnection of power supply the violation will be repeated within 90 seconds. If that’s
the case, the control panel will send a „zone alarm” message to the monitoring station, activate the
FIRE ALARM and FIRE/BURGLARY ALARM outputs, and trigger the fire alarm (intermittent signal) in
the keypad.
If there are no FIRE DETECTORS POWER SUPPLY outputs, the zone violation will immediately send
a „zone alarm” code to the monitoring station, activate the FIRE ALARM and FIRE/BURGLARY
ALARM type outputs, as well as trigger the fire alarm (intermittent signal) in the keypad.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Satel CA-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Satel CA-10 in the language / languages: English as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Satel CA-10

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 User Manual - English - 2 pages

Satel CA-10 Additional guide - English - 60 pages

Satel CA-10 Additional guide - English - 24 pages

Satel CA-10 User Manual - English - 24 pages

Satel CA-10 Quick start guide - English - 11 pages

Satel CA-10 User Manual - German - 2 pages

Satel CA-10 User Manual - German - 4 pages

Satel CA-10 Additional guide - German - 64 pages

Satel CA-10 Additional guide - German - 24 pages

Satel CA-10 User Manual - German - 26 pages

Satel CA-10 Installation Guide - German - 44 pages

Satel CA-10 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info