470265
51
Zoom out
Zoom in
Previous page
1/92
Next page
51
Setting
Picture in Picture
This function is used to project two videos simultaneously
by placing a separate small sub screen within or next to the
main screen.
Use the Point ed buttons to move the red frame pointer
to Picture in Picture and then press the SELECT button to
display a dialog box. You can also display the dialog box by
pressing and holding the PIP button on the remote control
for more than 3 seconds.
Use the Point 7 8 buttons to adjust the setting value.
Picture in Picture
....
Show the selected mode (Off/User1-
5) and its status (Stored /Free/Adj.).
'User1' and 'User2' have stored
default values. See page 30 for
details.
Main picture/
Sub picture .. Input: Select an input from Input 1-4.
Source: Select an input source. The display
varies depending on the selected
input.
Size: Select the display size. Main picture
can be changed between 10 and
100%, and Sub picture can be
changed between 10 to 50% in
increments of 10%.
Position: Press the SELECT button at
Position and the display position
setting screen appears. Use the
Point ed7 8 buttons to adjust
the display position of active frame
indicated in white. The frame will
disappear after 10 seconds or when
the SELECT button is pressed.
Frame Lock... Set the Frame Lock to Main picture or Sub
picture.
Reset ....... Press the SELECT button at Reset to
display a confirmation box. To reset, press
the SELECT button at [Yes].
Mode free ... Delete the data stored in the Mode and
return to the ‘Free‘ state. Use the Point 7
8 buttons to select Mode free and press
the SELECT button to show the 'Where
to free?' dialog box. Move the red arrow
pointer to one of the mode (Mode 1 - 5)
which you want to delete and press the
SELECT button. Then the confirmation box
appears. To delete, select [Yes].
Store........ Store the adjusted data in the User 1–5.
Use the Point 7 8 buttons to select Store
and press the SELECT button to show the
‘Where to store?‘ dialog box. Move the red
arrow pointer to one of the mode (Mode 1
- 5) in which you want to store and press
the SELECT button. Then the confirmation
box appears. To store adjusted data, select
[Yes].
Quit ........ Exit the Picture in Picture menu.
Picture in Picture
Use the Point 7 8
buttons to adjust
the setting value.
Selected Mode
Status (Stored /Free/
Adj.) of the selected
mode.
Close this dialog box.
To store the adjusted data.
Confirmation box appears
and then select [Yes].
This mode
has stored
data.
Vacant
Note:
The Picture in Picture function is not available depending
on the input signals and the selected input terminals. Refer
to ‘List of Picture in Picture‘ for details. (p.82)
When the input signal(s) is/are incompatible, X mark will
be displayed on the Main/Sub picture.
While the Main and Sub pictures are being displayed,
System, Image select, Image adj., Screen menus (except
for ‘Keystone’, ‘Ceiling’ and ‘Rear’), and DynamicBlack are
inoperative.
‘Progressive’ and ‘Noise reduction’ functions are fixed to
‘Off’ during the Picture in Picture operation. Therefore, the
image may become grainy depending on the input signal.
Active
frame
(White)
Center line
display
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo PDG-DET100L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo PDG-DET100L in the language / languages: English as an attachment in your email.

The manual is 10,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sanyo PDG-DET100L

Sanyo PDG-DET100L User Manual - German - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info