470265
91
Zoom out
Zoom in
Previous page
1/92
Next page
91
Appendix
Note:
The overlapping area might become uneven depending on the images. In such a case, it is recommended to
decrease the contrast of the images in the Image Adjust Menu or set the BrilliantColor function to ‘Off’.
If the colors of the left and right images do not match, then follow the next step.
Select ‘Color matching’ in the setting menu and display the Color matching dialog box.
Then, set ‘Color matching’ to ‘On’ and adjust the color settings (Red/Green/Blue/White).
(Refer to page 53 for operation procedure.)
6
Color matching
Note:
When you change the values of Target, make sure that each
Target value should be within the range of Measured value.
(e.g., In the case of the Fig.1, the X value of Target-Red
should be within 0.623 which is the X value of Measured-
Red.)
Set to ‘On.
5
Set ‘Test pattern’ to ‘On’ to display a 50 % white image. The overlap area will be brighter than the non-overlapping
area. Adjust the Black level in the Edge blending dialog box to increase the brightness of the non-overlapping area so
that the unevenness is reduced.
Select ‘Advanced color matching’ if you need further adjustment.
In the Advanced color matching dialog box, set ‘Advanced color matching’ to ‘On’ and adjust the values of Target (Red/
Green/ Blue/ Cyan/ Magenta/ Yellow/ White).
7
Fig.1 For rich color reproduction color wheel
If the colors of the left and right images do not match, even
if the Target values are adjusted, use a colorimeter which
is capable of measuring the chromaticity coordinates and
luminance. Follow the steps below.
1. Set ‘Auto test pattern’ to ‘On’ in the Advanced color
matching dialog box.
2. Put the cursor in the Mesured-White and press the
SELECT button to display a white pattern.
3. Measure the chromaticity coordinates (x,y) and
luminance (lx) by using the colorimeter.
4. Enter the obtained (x,y) values in the Mesured-White.
(The (L) value of Mesured-White should be left at 1.000.)
5. Put the cursor in the Mesured-Red and press the SELECT
button to display a red pattern.
6. Measure the chromaticity coordinates (x,y) and
luminance (Lx) by using the colorimeter.
7. Enter the obtained (x,y) values in the Mesured-Red. Then,
calculate the (L) value of Mesured-Red by applying the
following formula and enter the value.
(L) value of Mesured-Red = [Lx of Red] ÷ [Lx of White]
8. Enter the values of Mesured-Green, Mesured-Blue, and
Mesured-Half white in the same way as Mesured-Red.
9. Adjust the values of Target again.
10. Select ‘Store’ to complete. (Apply the same adjustment
to the other projector if necessary.)
8
91


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sanyo PDG-DET100L at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sanyo PDG-DET100L in the language / languages: English as an attachment in your email.

The manual is 10,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sanyo PDG-DET100L

Sanyo PDG-DET100L User Manual - German - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info