797034
10
Zoom out
Zoom in
Previous page
1/19
Next page
09
GB
F
E
NL
D
USING SCAN TUNING
The scan tuning feature of the ATS-909X2 can be used
on any band to automatically scan from the current
frequency to the nearest strong station with a higher /
lower frequency.
Follow these steps to use the scan feature:
1. Turn on the radio using the Power button (10).
2. Select the desired waveband by pressing the
corresponding button.
3. Press and hold one of the Tuning Up / Down buttons (18).
4. The radio now automatically scans for the nearest station
with a strong signal and a higher / lower frequency and
will play this station once it has been found.
5. Repeat step 4 to find to tune to other radio stations.
NOTE
The sensitivity of the scan tuning feature can be
adjusted by setting the squelch level. See "SETTING
THE SQUELCH LEVEL" section in chapter 5 for more
information.
USING MANUAL TUNING
Manual tuning can be used on any band to either input the
frequency of a radio station directly or to manually tune or
fine-tune to a station using small steps.
DIRECT TUNING
Follow these steps to directly tune to a radio station of
which you know the frequency:
1. Turn on the radio using the Power button (10).
2. Press the Freq button (25).
3. Use the numeric buttons (19) and the Decimal point
button (32) to enter the frequency.
Examples:
FM 107.85MHz: Press Freq (25) 1 0 7 .
8 → 5 → Enter
SW 25785kHz: Press Freq (25) → 2 → 5 → 7 → 8 → 5
→ Enter
Or Press Freq (25) 2 5 . 7 8 5
Enter
AIR 123.450MHz: Press Freq (25) 1 2 3 .
→ 4 → 5 → Enter
AM 1620kHz: Press Freq (25) 1 6 2 0
Enter
LW 257kHz: Press Freq (25) → 2 → 5 → 7 → Enter
NOTE
If the desired frequency is on the FM band, a decimal
point must be added when inputting the frequency.
MANUAL TUNING
To tune to a radio station of which you know the frequency
or to fine-tune to a station, follow these steps:
1. Turn on the radio using the Power button (10).
2. Select the desired waveband by pressing the
corresponding button.
3. Use the Rotary Tuning knob (16) or Tuning Up / Down
buttons (18) to tune to a higher / lower frequency.
SETTING THE TUNING STEP
When using manual tuning, the frequency change per
tuning step using the Rotary Tuning knob (16) and the FM
tuning step using the Tuning Up / Down buttons (18) can
be adjusted.
To adjust the Rotary Tuning knob (16) tuning step for the
SW, MW, LW, FM and AIR band, simply press the Step
button (17) when listening to a radio station. The Tuning
step indicator (O) on the display shows which tuning step
is currently selected. In addition, you can press and hold
the Step button (17) to disable tuning with the Rotary
Tuning knob (16). Hold the Step button (17) again to
enable tuning with the Rotary Tuning knob (16) again.
To adjust the FM tuning step of the Tuning Up / Down
buttons (18), follow these steps:
1. Press and hold the Menu button (29) to open the menu.
2. Use the Rotary Tuning knob (16) to select "FM STEP"
in the Text display (U).
3. Press the Step button (17) or Enter button (30) to start
configuring the setting.
The current FM tuning step will now blink in the Text
display (U).
4. Use the Rotary Tuning knob (16) to select 50kHz,
100kHz or 200kHz.
5. Press the Step button (17) or Enter button (30) to
confirm your choice.
6. Press the Menu button (29) to close the menu.
The MW / AM tuning step can be adjusted using the MW
/ AM tuning step switch (48), which is located inside the
battery compartment. This switch can be placed in either
the 9kHz or 10kHz position. In Europe and most other
parts of the world this switch must be placed in the 9kHz
position, while in America this switch must be placed in
the 10kHz position.
Finally, the ATS-909X2 also features a quick tuning
feature. This feature can be used by pressing and holding
the Enter button (30) while simultaneously rotating the
Rotary Tuning knob (16). Quick tuning allows for even
larger frequency steps, but it can only be used on the AIR,
FM and SW bands.
The following table shows the available tuning steps for
the Rotary Tuning knob (16) and the Tuning Up / Down
buttons (18) for each of the wavebands:
AIR FM LW MW SW
Rotary
Tuning
knob
STOP 0 0 0 0 0
FAST 25kHz 100kHz 9kHz 9kHz
10kHz 5kHz
SLOW 5kHz 50kHz 1kHz 1kHz 1kHz
Tuning Up /
Down (scan or
seek)
25kHz
50kHz
100kHz
200kHz
9kHz 9kHz
10kHz 5kHz
Quick Tuning 1MHz 1MHz - - 100kHz
STEREO RECEPTION
The ATS-909X2 is designed to receive FM stereo
broadcasts. When the radio is tuned to an FM station of
sufficient strength, the FM stereo indicator (Ab) will be
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sangean ATS-909X2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sangean ATS-909X2 in the language / languages: English as an attachment in your email.

The manual is 2.39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sangean ATS-909X2

Sangean ATS-909X2 User Manual - German - 20 pages

Sangean ATS-909X2 User Manual - Dutch - 21 pages

Sangean ATS-909X2 User Manual - French - 21 pages

Sangean ATS-909X2 User Manual - Spanish - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info