797034

Sangean ATS-909X2 Manual

11
Zoom out
Zoom in
Previous page
1/19
Next page
10
GB
F
E
NL
D
shown on the display and the broadcast will be played in
stereo if headphones are connected or an external device
is connected to the LINE OUT jack (38).
NOTE
The radio can be forced to play FM radio stations in
mono by using the "FM STEREO" setting in the menu.
This can help reduce noise when listening to FM
stations. More details on how to enable this feature can
be found in chapter 6 "USING THE MENU".
ADJUSTING THE VOLUME
The volume of the radio can be adjusted by rotating
the Volume Control knob (12) clockwise to increase the
volume or counterclockwise to decrease the volume.
USING PRESET STATIONS
The ATS-909X2 allows you to store up to 1674 radio stations
in the memory of the radio. The radio has three memory
banks that can each store up to 558 preset stations.
The following table gives an overview of the number of
stations that can be stored in one memory bank for each
of the wavebands:
WAVEBAND PRESET PAGES (9
PRESETS P PAGE)
TOTAL NO. OF
PRESETS
AIR 5 45
FM 4 36
MW 3 27
LW 1 9
SW 49 441
STORING PRESET STATIONS IN MEMORY
– MW / LW / FM / AIR
Follow these steps to save preset stations on the MW,
LW, FM and AIR bands:
1. Turn on the radio using the Power button (10).
2. Select the desired waveband by pressing the
corresponding button.
3. Tune to the station you want to store in the preset
memory as described earlier.
4. Press the Memo button (24).
The Memo indicator (X) and the first available preset
position (S) will now be blinking on the display.
5. To store the station at the first available position, press
the Enter button (30) to confirm and store the preset to
that position.
To store the station to a different preset position:
6. Press the Page button (27) to select the desired page.
7. Press any of the numeric buttons (19) to save the
station to the corresponding preset position.
NOTE
If another station has already been stored at a preset
position that is selected, then the station that was
previously stored at that preset position will be moved
to the rst available empty preset position (even if that
preset position is located on another page).
STORING PRESET STATIONS IN MEMORY
– SW ONLY
The procedure for storing stations on the SW band is
slightly different from the procedure for the other bands
described above. Follow these steps to store stations on
the SW band:
1. Turn on the radio using the Power button (10).
2. Select the SW band by pressing the SW button (20).
3. Tune to the station you want to store in the preset
memory as described earlier.
4. Press the Memo button (24).
The Memo indicator (X) and the first available preset
position (S) will now be blinking on the display.
5. To store the station at the first available position, press
the Enter button (30) to confirm and store the preset to
that position.
To store the station to a different preset position:
6. Use the Rotary Tuning knob (16) or Tuning Up / Down
buttons (18) to select a page number.
7. Now either press the Enter button (30) to save the
station to the first available position (S) on that page
or press any of the numeric buttons (19) to save the
station to the corresponding preset position.
If another station has already been stored at a preset
position that is selected, then the station that was
previously stored at that preset position will be moved
to the first available empty preset position on the same
page.
If a page on the SW band already has 9 stations preset
in the radio's memory, then you will have to either
select a different page manually or overwrite one of the
existing presets by pressing and holding the numeric
button of that preset position. Overwritten presets will
be moved to a different page if there are pages left with
available preset positions.
NOTE
NOTE
Because shortwave reception can be affected by
weather conditions, radio stations on the shortwave
band may have different frequencies on which they can
be received depending on the conditions. It is therefore
a good idea to store several frequencies for the same
radio station on the same preset page, as the radio
will automatically scan for the preset with the strongest
signal when a page is selected on the SW band.
RECALLING PRESET STATIONS – MW / LW
/ FM / AIR
Follow these steps to recall a preset station on the MW,
LW, FM and AIR bands:
1. Turn on the radio using the Power button (10).
2. Select the desired waveband by pressing the
corresponding button.
3. Select the page that the preset station is on (if
applicable) by repeatedly pressing the Page button (27).
4. Press any of the numeric buttons (19) to recall the
corresponding preset station.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sangean ATS-909X2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sangean ATS-909X2 in the language / languages: English as an attachment in your email.

The manual is 2.39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Sangean ATS-909X2

Sangean ATS-909X2 User Manual - German - 20 pages

Sangean ATS-909X2 User Manual - Dutch - 21 pages

Sangean ATS-909X2 User Manual - French - 21 pages

Sangean ATS-909X2 User Manual - Spanish - 21 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info