24757
13
Zoom out
Zoom in
Previous page
1/32
Next page
2TK LEVEL
The 2TK LEVEL control is used to adjust the amount of
signal that is sent from the 2TK IN jacks to the Control
Room or headphone outputs. For more information
see the section, "Playing back a CD Using the 2 Track to MIX" on page 18 of this manual.
Graphic Equalizer
The MDR16’s 9-band Graphic Equalizer allows you to contour the frequency response of the Left and Right MIX, or
the AUX1 mix for using monitors, providing a maximum of 12dB of cut/boost for each frequency band. This is an
especially useful tool for cutting frequencies that cause annoying feedback. The frequency response is flat when
the sliders are in the center position. Moving a slider in the positive direction will boost that frequency by as much
EQ IN/OUT
The MDR16’s internal 9-band Graphic Equalizer can be switched on or off using the EQ IN/OUT switch. When the
EQ IN/OUT switch is pressed in, the Green LED will illuminate indicating the EQ is active. Note: be sure to check
the position of the EQ TO AUX 1 switch, as described in the next section, to confirm the equalizer is routed to the
correct output.
EQ TO AUX 1
You can route the internal graphic equalizer to the AUX1 output using the EQ to AUX 1 switch. This is an especial-
ly useful feature if you want use the onboard equalizer on your AUX 1 monitor mix. To assign the internal graphic
equalizer to the AUX 1 output, press the EQ TO AUX1 switch in so that the green LED lights.
Controls and Functions
2 TRACK INPUT and OUTPUT
The MDR16’s 2 Track section provides the connections for
playback and recording for an external device such as a DAT,
cassette recorder, CD or Mini Disk.
MASTER SECTION
11
in the master section above the 3 /4 OUTPUTS faders, allowing you to subgroup channels. In this mode, you can
assign channels to the 3/4 bus and use the 3/4 OUTPUT faders to sub-mix those channels. More information on the
3/4 to MIX switch can be found later in this manual.
MUTE 3/4 OUTPUT ASSIGN Switch
The MUTE 3/4 switches are used to assign the channels to the 3/4 stereo bus. Any channels that have the 3/4
switch pressed in (the LED is on) will be heard in the 3/4 outputs.
In recording applications, you can use 3/4
switches with left and right panning to assign a channel to either the 3 or 4 bus outputs for sending to an input of
a recorder. You can also mix the 3/4 bus with the LEFT and RIGHT mix bus by using the 3/4 to MIX switch, located
in the master section above the 3 /4 OUTPUTS faders, allowing you to subgroup channels. In this mode, you can
assign channels to the 3/4 bus and use the 3/4 OUTPUT faders to sub-mix those channels. More information on the
3/4 to MIX switch can be found later in this manual.
FADER
The MDR16’s 60mm input FADER controls the overall channel level. The input FADER features an audio taper and
no detents for smooth fades.
23
24
25
26
(STEREO/DUAL-MONO INPUT CHANNEL CONTINUED)






































27
28
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson MDR16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson MDR16 in the language / languages: English as an attachment in your email.

The manual is 12,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info