24757
12
Zoom out
Zoom in
Previous page
1/32
Next page
Controls and Functions
HF (HIGH FREQUENCY)
12kHz +/- 15dB shelving type. The channel’s frequency response is flat when the
knobs are in the "12:00" position. Rotating the knob towards the right will boost the
corresponding frequency band by 15dB, and rotating it towards the left will cut the
frequency by 15dB.
LF (LOW FREQUENCY)
80Hz +/- 15dB shelving type. The channel’s frequency response is flat when the
knobs are in the "12:00" position. Rotating the knob towards the right will boost the
corresponding frequency band by 15dB, and rotating it towards the left will cut the
frequency by 15dB.
AUX 1/2 Switch
When the AUX1/2 switch is in the up position, the LED is off and the AUX send for
the dual/mono channel will be assigned to AUX1. If you are using the AUX 1 for a
monitor mix in a live sound application, you will be able to add the channel to the
monitor mix when the switch is set to AUX1. When the AUX1/2 button is pressed
down the green LED will illuminate, indicating that the Aux send will now feed the
AUX 2 bus. If you are using the AUX2 bus to drive the internal, 24 BIT digital effects,
you will be able to add effects to the channel when it is set to AUX2.
AUX Control Knob
The Aux 1/2 control knob
controls the amount of signal that is sent to the AUX 1 or 2
bus depending on the position of the AUX1/2 switch as described above
.
PAN
The MDR16’s PAN control is used to place or position the stereo signal into the main
Left and Right MIX bus. You can move a stereo signal’s image to the left or right by
setting the PAN control to the left or to the right.
SOLO Switch
When engaged, the yellow LED illuminates indicating the input channel is assigned
to the SOLO bus. The SOLO switch activates a logic control switch. Pressing the
switch repeatedly will assign the input channel on or off the SOLO bus. You can use the SOLO LEVEL control to
adjust the overall volume to the SOLO Bus.
MUTE 3/4 OUTPUT ASSIGN Switch
The MUTE 3/4 switches are used to assign the channels to the 3/4 stereo bus. Any channels that have the 3/4
switch pressed in (the LED is on) will be heard in the 3/4 outputs.
In recording applications, you can use 3/4
switches with left and right panning to assign a channel to either the 3 or 4 bus outputs for sending to an input of
a recorder. You can also mix the 3/4 bus with the LEFT and RIGHT mix bus by using the 3/4 to MIX switch, located




















































16
17
18
19
20
21
(STEREO/DUAL-MONO INPUT CHANNEL CONTINUED)
CHANNEL EQUALIZER
The MDR16 Stereo/Dual-mono input channels feature a 2-band equalizer allowing you to adjust the high and low fre-
quencies independently on each channel. The channel’s frequency response is flat when the knobs are in the "12:00"
position. Rotating the knob towards the right will boost the corresponding frequency band by 15dB, and rotating it
towards the left will cut the frequency by 15dB. The frequency centers, range of boost or cut, and equalizer type for each
band are as follows:
22
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Samson MDR16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Samson MDR16 in the language / languages: English as an attachment in your email.

The manual is 12,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info