Manual Samson MDR16 (page 10 of 32) (English)

24757

Zoom out

Zoom in

1/32

(MONO INPUT CHANNEL CONTINUED)

AUX 1 SEND

The MDR16 has two auxiliary sends which can be used for sending signals to the

external effects devices or for creating a monitor mix. The AUX1 section is often used

for a monitor mix in a live sound application, or for a headphone mix in a recording

application. Each input channel includes an AUX 1 send which controls the amount of

that channel’s signal that is sent to the AUX 1 bus. The Input channels' AUX 1 sends are

mixed together and are sent to the AUX 1 OUT jack.

AUX 1 PRE/POST switch

On channels 1 through 8, it is possible to set the Aux 1 control knob to send signal

from before (PRE) or after (POST) the channel fader. Following is a description of the

signal paths.

PRE FADER AUX send - If you want to use AUX 1 as a send for a monitor, set the PRE/POST switch to the up or PRE

position. When AUX 1 is set to “PRE”, the channel’s signal will be sent directly to the AUX1 output using the chan-

nel AUX 1 control knob. In this mode the channel fader has no effect on the signal being sent from the AUX1 knob.

So in a stage monitor situation, only the Aux 1 knob, and not the channel fader, controls the level sent to the AUX1

output, and therefore, the overall volume of that channel in the monitors.

POST FADER AUX send - If you want to use AUX 1 as a send to an effects processor, set the PRE/POST switch to the

down or POST position. In this mode the channel signal will be sent to the AUX1 output using the channel AUX 1

control knob in conjunction with the channel fader. So when using AUX 1 for a mix being sent to an effects proces-

sor, the Aux 1 knob, and the channel fader both control the overall level sent to the AUX1 output. If you are sending

to a delay or reverb, when you push the channel fader up you are sending more signal to the delay or reverb. Pull

the fader down and you are sending less level to the delay or reverb. Keep in mind that when the AUX 1 is in POST,

the Aux send follows the fader.

AUX 2 / DSP Send

The MDR16 provides high quality, 24 Bit digital effects, and the level of effects can be set independently on

each channel. The channel’s AUX 2/DSP knob controls the amount of signal that is sent to the AUX 2/DSP bus.

The signal of the AUX 2/DSP bus is routed to the internal DSP effects section for onboard signal processing. The

AUX 2/DSP signal can also be sent to an external effect device connected to the AUX 2 OUT jack located in the

MASTER SECTION jack field.

NOTE

: The channel’s AUX 2/DSP signal is sent to the AUX 2/DSP bus from a location in the signal path

after

the

channel’s LEVEL control. This is commonly referred to as a POST FADER send. This means that the amount of signal

that is sent to the EFFECT bus will be affected not only by the setting of the AUX 2/DSP knob control, but it will also

be affected by the setting of the LEVEL control.

PAN

The MDR16’s PAN control is used to place or position the mono signal into the stereo main Left and Right MIX bus.

You can create a stereo image by panning some input signals to the left and others to the right. The MDR16’s PAN

control is a Power-Pan circuit, which includes a 3dB dip in the center position. This is desirable since there’s a 3dB

increase in gain when the mono input signal is heard at the same level in both the Left and Right MIX bus.









































Controls and Functions

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Samson MDR16 in the language / languages: English as an attachment in your email.

The manual is 12,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Samson MDR16 Manual

Product: