647727

Salter BPA-9200 Manual

6
Zoom out
Zoom in
Previous page
1/16
Next page
GB
6
—Consult the dealer or an experienced radio/TV technician for help.
17. This blood pressure monitor is verified by auscultatory method. It is recommended that you check annex B of ANSI/AAMI
SP-10:2002+A1:2003+A2:2006 for details of verification method if you need.
SETUP AND OPERATING PROCEDURES
1. BATTERY LOADING
a. Open battery cover at the back of the monitor.
b. Load four “AA” size batteries. Please pay attention to polarity.
c. Close the battery cover.
When LCD shows battery symbol , replace all batteries with new ones.
Rechargeable batteries are not suitable for this monitor.
Remove the batteries if the monitor will not be used for a month or more to avoid relevant damage of battery leakage.
Avoid the battery fluid to get in your eyes. If it should get in your eyes, immediately rinse with plenty of clean water and
contact a physician.
The monitor, the batteries and the cu, must be disposed of according to local regulations at the end of their usage.
2. CLOCK AND DATE ADJUSTMENT
a. Once you install the battery or turn o the monitor, it will enter Clock Mode, and LCD will display time and date by turns.
See picture 2 & 2-1.
Picture 2 Picture 2-1 Picture 2-2
b. While the monitor is in Clock Mode, pressing both the “START” and “MEM” button simultaneously, a beep is heard and the
month will blink at first. See picture 2-2. Press the button “START” repeatedly, the day, hour and minute will blink in turn.
While the number is blinking, press the button “MEM” to increase the number. Keep on pressing the button “MEM”, the
number will increase fast.
c. You can turn o the monitor by pressing “START” button when the minute is blinking, then the time and date is confirmed.
d. The monitor will turn o automatically after 1 minute of no operation, with the time and date unchanged.
e. Once you change the batteries, you should readjust the time and date.
3. CONNECTING THE CUFF TO THE MONITOR
Insert the cu tubing connector into the socket in the left side of the monitor. Make certain that the connector is completely
inserted to avoid air leakage during blood pressure measurements.
Avoid compression or restriction of the connection tubing during measurement, which may cause inflation error, or
harmful injury due to continuous cu pressure.
… 6 …


Need help? Post your question in this forum.

Forumrules
1

Forum

salter-bpa-9200

Reset search

  • is it possible to replace the salter monitor cuff model BPA-9200-GB and how much would that cost ?

    I keep getting Er 4 whenever I try to use it.. I have used it looser before without being told the problem is that I do not tighten it enough on my arm . Any advice please?
    Thank you Abbas Baba Submitted on 27-4-2021 at 16:45

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Salter BPA-9200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Salter BPA-9200 in the language / languages: English as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info