647727

Salter BPA-9200 Manual

7
Zoom out
Zoom in
Previous page
1/16
Next page
GB
7
4. APPLYING THE CUFF
a. Pulling the cu end through the medal loop (the cu is packaged like this already), turn
it outward (away from your body) and tighten it and close the Velcro fastener.
b. Place the cu around a bare arm 1-2cm above the elbow joint.
c. While seated, place palm upside in front of you on a flat surface such as a desk or table.
Position the air tube in the middle of your arm in line with your middle finger.
d. The cu should fit comfortably, yet snugly around your arm. You should be able to insert
one finger between your arm and the cu.
Note:
1. Please refer to the cu circumference range in “SPECIFICATIONS” to make sure that the
appropriate cu is used.
2. Measuring on same arm each time.
3. Do not move your arm, body, or the monitor and do not move the rubber tube during measurement.
4. Stay quiet, calm for 5 minutes before blood pressure measurement.
5. Please keep the cu clean. If the cu becomes dirty, remove it from the monitor and clear it by hand in a mild detergent,
then rinse it thoroughly in cold water. Never dry the cu in clothes dryer or iron it. Clean the cu after the usage of every
200 times is recommended.
5. BODY POSTURE DURING MEASUREMENT
Sitting Comfortably Measurement
a. Be seated with your feet flat on the floor, and don’t cross your legs.
b. Place palm upside in front of you on a flat surface such as a desk or table.
c. The middle of the cu should be at the level of the right atrium of the heart.
Lying Down Measurement
a. Lie on your back.
b. Place your arm straight along your side with your palm upside.
c. The cu should be placed at the same level as your heart.
6. TAKING YOUR BLOOD PRESSURE READING
a. After applying the cu and your body is in a comfortable position, press the “START” button. A beep is heard and all
display characters are shown for self-test. See picture 6. Please contact the service center if segment is missing.
b. Then the current memory bank (U1 or U2) is blinking. See picture 6-1. Press “MEM” button to change over to other
bank. See picture 6-2. Confirm your selection by pressing “START” button. The current bank can also be confirmed
automatically after 5 seconds with no operation.
Picture 6 Picture 6-1 Picture 6-2
c. After selecting the memory bank, the monitor starts to seek zero pressure. See picture 6-3.
… 7 …


Need help? Post your question in this forum.

Forumrules
1

Forum

salter-bpa-9200

Reset search

  • is it possible to replace the salter monitor cuff model BPA-9200-GB and how much would that cost ?

    I keep getting Er 4 whenever I try to use it.. I have used it looser before without being told the problem is that I do not tighten it enough on my arm . Any advice please?
    Thank you Abbas Baba Submitted on 27-4-2021 at 16:45

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Salter BPA-9200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Salter BPA-9200 in the language / languages: English as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info