661079

Sabo 54-K VARIO B Manual

42
Zoom out
Zoom in
Previous page
1/100
Next page
8
Filling with oil (Illustration Y1 )
Pos: 16.8 /Innenteil/Sicherheitshinweise/Sicherheitshinweis: Explosion @ 0\mod_1115210618640_1521.docx @ 1527 @ @ 1
Safety instruction!
See table for explanation of symbols page 3
Pos: 16.9 /Innenteil/Vor der Ersten Inbetriebnahme/Öl einfüllen Hinweis Motor JS63 @ 3\mod_1158825745978_1521.docx @ 20353 @ @ 1
IMPORTANT
Avoid damage! Engine is delivered without oil. You must add oil before running
the engine.
Pos: 16.10 /Innenteil/Vor der Ersten Inbetriebnahme/Öl einfüllen Text Motor SUBARU @ 23\mod_1371468831546_1521.docx @ 175894 @ @ 1
Before starting the engine for the first time, use a funnel to fill motor oil (quantity and
quality see technical data) having unscrewed the dipstick in this opening first.
– Set the mower on level ground.
– Slowly fill oil through the filler neck. Do not overfill.
– Check oil level
Remove the dipstick. Use a clean cloth to wipe off the dipstick, then insert it again
but do not screw tightly. Then pull the dipstick out again and read off the oil level.
The oil must be between the "L" and "H" marks. Replenish oil if necessary.
However, the oil must not be higher than the "H" mark on the dipstick. Overfilling
will lead to engine damage.
Insert the oil dipstick again and tighten.
– After initial filling, remove the "NO OIL" sign from the top of the engine.
Pos: 16.11 /Innenteil/Vor der Ersten Inbetriebnahme/1.1 Kraftstoff einfüllen @ 0\mod_1115211956203_1521.docx @ 1710 @ 2 @ 1
Filling with fuel
Pos: 16.12 /Innenteil/Sicherheitshinweise/Sicherheitshinweis: Explosion, Benzin @ 0\mod_1115211811093_1521.docx @ 1528 @ @ 1
Safety instruction!
See table for explanation of symbols page 3
Pos: 16.13 /Innenteil/Vor der Ersten Inbetriebnahme/Kraftstoff einfüllen Text mit Kraftstoffhahn (A), Subaru, kein Alkylatbenzin @ 45\mod_1470293273417_1521.docx @ 512011 @ @ 1
– Only fill the tank with fresh and clean unleaded standard petrol. Never use
alkylate-based petrol.
Fuel with up to 10% ethanol or 15% MTBE content is acceptable.
Never use petrol with an ethanol content greater than 10% or an MTBE content
greater than 15% since this can lead to damage to the engine or fuel system.
– Fuel tap should be closed A !
– Unscrew the fuel cap.
– Use a funnel to fill the fuel up to the max. lower edge of the filling nozzle.
– Replace the fuel filler cap and screw tight.
Pos: 17.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
Pos: 17.2 /Innenteil/Starten des Motors/1 STARTEN DES MOTORS (Abbildung A + C + E ) @ 9\mod_1225698649269_1521.docx @ 69053 @ 1 @ 1
10 STARTING THE ENGINE (Illustration A + C + E )
Pos: 17.3 /Innenteil/Starten des Motors/Allgemeine Sicherheitshinweise BBC @ 0\mod_1127887846473_1521.docx @ 1736 @ @ 1
Only start the engine when standing behind of the mower.
Pos: 17.4 /Innenteil/Starten des Motors/Starterseilgriff während des Startens fest umfassen Hinweis @ 13\mod_1280234045462_1521.docx @ 110218 @ @ 1
CAUTION
Hold the starter cable handle firmly when starting. The handle may otherwise slip
out of your hand. Risk of injury!
Pos: 17.5 /Innenteil/Starten des Motors/Starten des Motors Text SubaruI BBC 47/54-K VARIO B @ 34\mod_1415279044769_1521.docx @ 249807 @ @ 1
– Open the fuel tap (1) A .
– Push the engine actuation lever (2) to the position "MAX" (3) C .
– Slowly pull the starter cable (4) out until resistance can be clearly felt.
Now return the handle to its initial position and then rapidly pull it out E – the
engine begins to run, slowly rewind the cable.
– In the position "MAX" the engine is running with maximum power at maximum
speed, which is required for a clean cutting pattern (engine speed = blade speed).
– For the grass collecting bag to be emptied, the lever (2) can be pushed to the
position (5) C .
Pos: 18.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
Pos: 18.2 /Innenteil/Einschalten des Mähwerks/1 EINSCHALTEN DES MÄHWERKS (Abbildung H3 ) @ 0\mod_1128001611856_1521.docx @ 1743 @ 1 @ 1
11 SWITCHING ON THE CUTTING DECK (Illustration H3 )
Pos: 18.3 /Innenteil/Sicherheitshinweise/Sicherheitshinweis: Fuss, Stein, Abstand @ 0\mod_1115212854781_1521.docx @ 1529 @ @ 1
Safety instruction!
See table for explanation of symbols page 3
Pos: 18.4 /Innenteil/Einschalten des Mähwerks/Allgemeine Sicherheitshinweise @ 26\mod_1378131771352_1521.docx @ 195634 @ @ 1
Only switch on the cutting deck when standing behind the mower.
Always place the mower on a level area which is not covered with high grass (if the
grass is too high it will block the cutter bar start-up and make starting the mower more
difficult). When the engine is started, the machine must not be tilted on end, if
necessary it must be tilted by pressing the guide bar down so that the cutting tool is
pointing in the direction away from the user, but only as far as absolutely necessary. As
long as the mower has not been lowered to the ground again, both your hands must be
on the top part of the bar.
Pos: 18.5 /Innenteil/Einschalten des Mähwerks/Einschalten des Mähwerks Text @ 0\mod_1127888544154_1521.docx @ 1745 @ @ 1
– Press and hold down the safety control bracket (1) against the upper section of the
handlebar.
– Push the lever (2) quickly forward as far as the stop, and then release. The lever
returns automatically to its starting position.
Pos: 18.6 /Innenteil/Einschalten des Mähwerks/Hinweis: WICHTIG @ 1\mod_1131614611084_1521.docx @ 4987 @ @ 1
IMPORTANT
Switching on the cutting deck slowly will lead to excessive wear to the brake and
clutch fittings and overheating of the complete brake clutch system.
For trouble-free operation of the starting system, the cutting deck must be
started according to the sequence specified above.
Pos: 19.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
Pos: 19.2 /Innenteil/Ausschalten des Mähwerks/1 AUSSCHALTEN DES MÄHWERKS (Abbildung I3 ) @ 1\mod_1131612621303_1521.docx @ 4971 @ 1 @ 1
12 SWITCHING OFF THE CUTTING DECK (Illustration I3 )
Pos: 19.3 /Innenteil/Ausschalten des Mähwerks/Ausschalten des Mähwerks Text @ 1\mod_1131614534722_1521.docx @ 4979 @ @ 1
– Quickly release the safety switch bar for the blade brake.
Pos: 19.4 /Innenteil/Ausschalten des Mähwerks/Hinweis: WICHTIG @ 1\mod_1131614983250_1521.docx @ 4995 @ @ 1
IMPORTANT
As soon as the safety control bracket is released, it springs back to its starting
position under spring pressure, the blade brake now comes into operation, and
the blade is brought to a standstill within 3 seconds.
Pos: 20.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
Pos: 20.2 /Innenteil/Abstellen des Motors/1 ABSTELLEN DES MOTORS (Abbildung I3 + G3 + A ) @ 9\mod_1225699035480_1521.docx @ 69069 @ 1 @ 1
13 SWITCHING OFF THE ENGINE (Illustration I3 + G3 + A )
Pos: 20.3 /Innenteil/Abstellen des Motors/Abstellen des Motors Text BBC mit Kraftstoffhahn (Abbildung I3 + G3 + A) @ 9\mod_1225699202814_1521.docx @ 69085 @ @ 1
– Quickly release the safety switch bar for the blade brake I3 .
– Move the operating lever to the STOP position G3 .
– Close the petrol tap A .
Pos: 20.4 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
Pos: 20.5 /Innenteil/Abstellen des Motors/1 ANHALTEN IM NOTFALL @ 5\mod_1183556328817_1521.docx @ 36114 @ 1 @ 1
14 EMERGENCY STOPPING
Pos: 20.6 /Innenteil/Abstellen des Motors/Anhalten im Notfall Text m.A. BBC @ 5\mod_1183557276903_1521.docx @ 36179 @ @ 1
Release the safety control lever and the drive switch bar.
– The mower will stop.
– The blade will stop.
Pos: 20.7 /Innenteil/Abstellen des Motors/Anhalten im Notfall Hinweis BBC @ 26\mod_1378132186846_1521.docx @ 195685 @ @ 1
NOTE
Before every mowing job, make sure that the safety control bar for the blade
brake and the motor drive control bar are working perfectly:
– when the safety control bar is released, the cutter bar must come to a
standstill within three seconds.
– when the motor drive control bar is released, the machine must come to a
standstill immediately.
If this is not the case, please consult your nearest authorised workshop.
Pos: 21.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
Pos: 21.2 /Innenteil/Fahrantrieb/1 FAHRANTRIEB @ 0\mod_1115215262046_1521.docx @ 1759 @ 1 @ 1
15 MOVEMENT DRIVE
Pos: 21.3 /Innenteil/Fahrantrieb/1.1 Bedienung des Hinterradantriebes (Abbildung G ) @ 0\mod_1115216300453_1521.docx @ 1760 @ 2 @ 1
Operating the rear wheel drive (Illustration G )
Pos: 21.4 /Innenteil/Fahrantrieb/Bedienung des Hinterradantriebes Text BBC 47er Redesign/54er SABO+JD @ 37\mod_1435578513572_1521.docx @ 397581 @ @ 1
The rear wheel drive is switched on and off by means of the drive control bar (1) on the
top guide bar (2) when engine and mowing blade are running:
– Pull and hold the drive control bar = mower moves.
– Release the drive control bar = mower stops (0-position).
When driving outside the lawn on paths or roads, only switch on the drive when the
engine is running.
NOTE
The rear wheels click when the mower is pushed forwards.
47-K VARIO B, R47KB
The drive control bar must always be pulled tight to the top bar. Incorrect actuation will
lead to gearbox wear. The initial greater resistance of the bar is intentional and makes it
more difficult to make operating errors.
Pos: 21.5 /Innenteil/Beschreibung der Bauteile/Alle Modelle_dl_text_bold_8 @ 33\mod_1409212920947_1521.docx @ 245827 @ @ 1
All models
Pos: 21.6 /Innenteil/Fahrantrieb/1.1Geschwindigkeitseinstellung (Abbildung H ) @ 0\mod_1127891247101_1521.docx @ 1761 @ 2 @ 1
Adjusting the speed (Illustration H )
Pos: 21.7 /Innenteil/Fahrantrieb/Geschwindigkeitseinstellung Wichtig @ 0\mod_1127891394613_1521.docx @ 1764 @ @ 1
IMPORTANT
The speed may only be adjusted when the engine is running in order to avoid
damage!
Pos: 21.8 /Innenteil/Fahrantrieb/Geschwindigkeitseinstellung Text Drehgriff MUSTER @ 17\mod_1334232318791_1521.docx @ 137078 @ @ 1
The driving speed is set using the rotary knob mounted on the left.
– The knob can be turned in both directions for speed adjustment, so that the
required driving speed can be set. The arrow on the knob indicates the driving
speed.
– Position “Hare” = fast (max. speed)
– Position “Tortoise” = slow (min. speed)
NOTE
Mowing at high speed leads to poor cutting pattern or collection result. Always
adapt the speed to the prevailing conditions. For longer grass sections, a slower
driving speed should be selected.
Pos: 22.1 /---------- 1 Leerzeile ---------- @ 0\mod_1114611787140_1521.docx @ 2070 @ @ 1
… 42 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Sabo 54-K VARIO B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Sabo 54-K VARIO B in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 3,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info