512484

Robomow Tuscania 500 Manual

91
Zoom out
Zoom in
Previous page
1/268
Next page
EN
37
Chapter 4 - Text Messages and Troubleshooting
4.1 Messaging
Robomow is equipped with an LCD panel that will notify you in the form of a text message when common
operational faults occur to instruct the user to perform a certain function or action.
If the LCD screen is blank, pressing the ‘GO’ button one time will wake the mower up and the last fault or
message displayed prior to stopping will now be displayed. If a specific problem re-occurs, it is
recommended to identify the fault code prior to calling for service. Pressing the
‘UP’ arrow once, while the
message is displayed, is a shortcut button to display the
‘Last stop cause’ (refer to paragraph 2.3.5).
Message
Displayed
Probable Cause/Event Corrective/User Action
Adjust wire
then press GO
- Robomow detects an obstacle along the
edge while operated in ‘Wire position test’
mode.
- Adjust the wire in the place where it
collides in the obstacle or remove the
obstacle and then press ‘GO’ to continue
in the wire position test.
Base problem
- Robomow fails to enter the Base Station 3
times continuously
- Adjust the Base Station position.
- Clean the contacts with a brush or piece of
cloth.
- Confirm a good connection of the cables to
the Base Station contacts.
- Confirm the Base Station is leveled with
the ground before the Base, so there is no
step that causes Robomow to slips.
Bumper pressed
- Bumper is constantly being pressed
- Move mower away from object pressing
against bumper.
Change wires in
plot connector
- This message appeared at the first time the
‘GO’ button is pressed after completing the
setup in case the perimeter wire is
connected to the plot connector in the wrong
polarity.
- Change between the two wires ends that
connected to the plot connector (the green
connector that connected to the Base
Station).
Charging failure
- The charging process is not active - Contact service provider
Check mow height
- Mowing motor has faced over-current for too
long because of high grass or some obstacle
is stuck or wrapped around the blade.
- Something is preventing a blade from
rotating freely. Severe grass accumulation
under the mowing deck; rope or similar
object wrapped around mowing blade.
- Object jammed under mower preventing
blade from rotating.
CAUTION
– Remove fuse before lifting the
mower.
- Inspect blades for foreign material or
debris preventing rotation.
- Clean out accumulated grass clippings
using a wooden stick.
- Power supply is not plugged properly into the
main power supply
- The charging process has stopped due to a
temporary power loss.
- Confirm power supply is plugged into the
main power receptacle.
- No power to receptacle or main power is
shut off
- Turn power on to the main receptacle.
- Check the mains supply using another
appliance
- The mower or Charging Station contacts are
dirty
- Clean the contacts with a brush or piece of
cloth
Check power
(Base Station)
- Charging is not detected, although there is
physical contact between the mower and the
Base Station contacts.
- Confirm a good connection of the power
supply to the Base Station.
- Confirm a good connection of the Base
Station board cables (green and red) to
the Base Station contacts pins (screws
are tightened).
… 91 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow Tuscania 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow Tuscania 500 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 9,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info