512484

Robomow Tuscania 500 Manual

92
Zoom out
Zoom in
Previous page
1/268
Next page
EN
38
Message
Displayed
Probable Cause/Event Corrective/User Action
- Power supply cable is not plugged properly
into the mains supply.
- Confirm power supply is plugged into
the main power receptacle.
Check power
(Winter charger)
- No power to receptacle or main power is
shut off
- Turn power on to the main receptacle.
- Check the mains supply using another
appliance
Check signal
Press GO
- There is no fitting between the 'Signal type'
setting in the menu and the signal jumper on
the Perimeter Switch;
- Automatic operation is initiated while
Robomow is placed out of the perimeter wire
lope.
- The perimeter wire is connected to the plot
connector in the wrong polarity.
- Robomow detects signal interferences from
adjacent activated lawn or from other
appliance activated near the zone;
- Set the 'Signal type' menu to 'A' and
confirm the signal jumper is installed on
the Perimeter Switch board; or
alternatively set it to 'B' and remove the
signal jumper from the board;
- Place the mower inside the lawn and
press the ‘GO’ button.
- Change between the two wires ends that
connected to the plot connector (the
green connector that connected to the
Base Station).
- In case of signal interference call the
service for help;
Check wire
- Poor connection of perimeter wire - twisted
cables, or a screw terminal, insulated with
insulation tape is not a satisfactory splice.
Soil moisture will cause the conductors to
oxidize and after a while result in broken
circuit.
- Too long perimeter wire
- Check and repair all loose/poor or
corroded connections.
- Use only the connectors supplied in the
box. It is waterproof and gives a reliable
electrical connection.
- The maximum length of wire allowed in
one lope is 500m – if the wire is longer
than 500m, split the area into 2
separated zones.
Close cover
- The bumper cover is not in its place because
one of the following reasons:
1.The cover has popped out during
operation while Robomow has collided in
obstacle.
2. The bumper cover was not placed
properly by the user in its place.
1. In case of short / slanted obstacles, it
must be protected from the
Robomow using the perimeter wire
around it.
2. Press the bumper cover downwards
and confirm it is clicked well.
- The perimeter wire is too close to the edge
- The lawn slope is too big
- Robomow does not succeed to turn in place
at the edge and it causes the mower to slip
out of the area.
- Too low cutting height for the lawn and grass
conditions.
- Remove the wire towards the inner side
of the lawn and do not include area with
too big slopes.
- Fill any holes and pits in the ground.
- Increase the cutting height
Cross wire
- Short-circuit detected in Drive Motors. - Contact your Service Dealer.
Drive overheat
cooling, wait…
- The drive motors have been working under a
severe load for too long.
- There is no need to do anything
Robomow will renew automatically the
operation, as the drive motor will cool
down.
Failure: xyz
- Internal failure
- Press ‘go’ to confirm the message; if the
message is still displayed, remove the
battery fuse for 10 seconds and retry to
operate the mower. If the message still
displayed, contact your service dealer.
… 92 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow Tuscania 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow Tuscania 500 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 9,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info