512484

Robomow Tuscania 500 Manual

89
Zoom out
Zoom in
Previous page
1/268
Next page
EN
35
3.5 Operation in Base Zone – Manual Start
Manual Depart mode can be used in cases such as the following:
- Mowing the lawn at times other than when programmed.
- When the lawn is occupied and the yard must be cleared of debris, objects, pets or people first.
For initiating a manual start for mowing, press the ‘GO’ button once. Robomow will depart from the
Base Station and will mow the edge until it reaches the Base Station. It will reverse out and move
back to continue mowing of the inner area.
To skip the edge mowing process, press the ‘GO’ button twice when initiating manual start and
mowing.
3.6 Returning to the Base Station
Automatic Return
Robomow automatically returns to the Base Station at the end of every operation. It will recharge
and stay ready for the next scheduled start time that was scheduled.
‘Go to base’ option
You can manually send the mower to the Base Station from any point in the lawn by pressing the
upper scroll arrow once for the
‘Go to base’ message option - then press ‘GO’. The Robomow will
find the perimeter wire and will follow it until reaching the Base Station –
‘Searching base’
message is displayed during this sequence.
3.7 Operation in None-Base Zone
Non-Base Zone is defined as a separated area, where the user must drive the mower manually from
the Base Station or carry it by hand, to the area in order to mow it. It can be operated either by the
Perimeter Switch or the Base Station.
Important! When mowing in non-Base zone, it is required first to define the work time (refer to 2.1.2)
and to set the proper time depends on the zone area.
Zone activation
Connected to the Base Station - the zone is activated automatically as the mower is taken out from
the Base Station. If an intermittent beeping is heard shortly after turning the switch on, there is a
problem of cut wire or poor wire splicing (refer to chapter 4 – Text messages and Troubleshooting
for further help). Listen to the beeps to identify the problem (refer to figure 1.24). You must correct
the problem before Robomow can operate automatically.
Connected to Perimeter Switch
- Robomow cannot operate unless the Perimeter Switch is turned
on. Press the
on/off button to turn on the switch. To verify switch operation, there is a green LED
located next to the button that will flash when operating properly. If an intermittent beeping is heard
shortly after turning the switch on, there is a problem of cut wire or poor wire splicing (refer to
chapter 4 – Text messages and Troubleshooting for further help). Look to see which of the red
LEDs is flashing to identify the problem (refer to figure 1.43). You must correct the problem before
Robomow can operate automatically.
Place the mower inside the active perimeter.
Press the ‘GO’ button. In a case where you have forgotten to turn on the Perimeter Switch, a ‘No
wire signal’ message will be displayed, reminding you to turn the switch on.
3.8 Completing the Operation
Base Station Zone –
When Robomow has operated the allotted time, it will switch off the mowing motor and will start
moving in lines towards one of the lawn edges, then it will follow the perimeter wire back to the Base
Station, to be charged and get ready for the next operation.
… 89 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robomow Tuscania 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robomow Tuscania 500 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 9,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info