520097

Robbe Futaba FF-10 Manual

85
Zoom out
Zoom in
Previous page
1/119
Next page
85
Camber Mixing (
CAMBER MIX
)(
GLID
):
This function adjusts the mixing rate of camber operation which operates the
wing camber (ailerons and fl aps) in the negative and positive directions. The
aileron, fl ap, and elevator rates can also be adjusted independently and attitude
changes caused by camber operation can be corrected.
Also the operation reference point of camber control can be offset. (
PRE
)
NOTE: Camber control is not assigned at initial.
GOAL of EXAMPLE: STEPS: INPUTS:
Ex: Set the mixing amount for aileron
to
40
%, camber control to VR(E),
reference point to desired point.
Open the
CAMBER MIX
function.
for 1 second.
(If
BASIC
, again.)
C
to
CAMBER MIX
.
Choose desired slider.
C
to
VR
. to VR(E).
Adjust the mixing amount for
AILE
.
(Ex: adjust to
40%
.)
C
to
AILE
. VR(E). to
40%
.
VR(E). to
40%
.
Set the reference point.
C
to
PRE
. or VR(E) to
desired point.
for one second.
Close menu.
Adjustability:
• Rate: -100% to +100%, with a default of +30%
•
Reference point (
PRE
): The operation reference point of camber control can be offset. -100% to +100%, with a default of 0%.
START DELAY
(
GLID 1A+1F
only):
START DELAY
automatically switch the offset trims (
OFFSET
) from the
START
condition's trims to the normal cndition's trims after proceeding the delay time
(max.10sec.) which is set by the
-dly-
item when activating the
START
condition.
(It is convenient for hand launch glider.)
NOTE: The same delay amount for elevator and rudder is recommended when
using V-tail function.
Adjustability:
• Delay time (
-dly-
) range of 0 to 100%. The delay time is 10 second at 100%.
GOAL of EXAMPLE: STEPS: INPUTS:
Ex: delay time=5 second. Open
ADVANCE
menu, then open
START
DELAY
function.
for 1 second.
(If
ADVANCE
, again.)
C
to
START DELAY
.
Activate the function.
C
to
MIX
. to
OFF
or
ON
.
Set the delay time.
(Ex:
50%
each surface)
C
to
ELEV
. to
5O%
.
C
to
RUDD
. to
5O%
.
Repeat as needed.
Close.
… 85 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba FF-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba FF-10 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba FF-10

Robbe Futaba FF-10 User Manual - German - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info