520097
58
Zoom out
Zoom in
Previous page
1/119
Next page
58
Using
V-TAIL
(
ACRO
/
GLID
):
V-TAIL
mixing is used with v-tail aircraft so that both elevator and rudder
functions are combined for the two tail surfaces. Both elevator and rudder travel
can be adjusted independently on each surface.
NOTE: If
V-TAIL
is active, you cannot activate
ELEVON
or
AILEVATOR
functions. If one of these functions is active, an error
message will be displayed and you must deactivate the last function prior to activating
ELEVON
. see the wing example on
page 51.
NOTE: Be sure to move the elevator and rudder sticks regularly while checking the servo motions. If a large value of
travel is speci ed, when the sticks are moved at the same time, the controls may bind or run out of travel. Decrease the
travel until no binding occurs.
Adjustability:
Requires use of CH2 and CH4.
Independently adjustable travels allow for differences in servo travels.
Rudder differential is not available. (To create rudder differential, set
RUD1
and
2
to
0
, then use two programmable mixes,
RUD-ELE
and
RUD-RUD
, setting different percents for up and down. These are your new rudder travels. Trim and link off,
switch assignment null so you can’t accidentally turn off rudder. see
PROG.MIX
, p. 68.)
(For details on setting up a complex plane, such as one with a v-tail AND a separate steerable nosewheel, please visit our
FAQ at www.futaba-rc.com\faq\. Many other setup examples are also available at this location.)
GOAL of EXAMPLE: STEPS: INPUTS:
Activate
V-TAIL
.
Adjust left elevator servo to
95%
travel
to match to right servo's travel.
Open the
V-TAIL
function.
for 1 second.
(If
BASIC
, again.)
C
to
V-TAIL
.
Activate the function.
C
to
MIX
. to
ACT
.
optional: adjust the travels separately
for the 2 servos as elevators. (Ex: set
left to
95%
.)
C
to
ELE1
. to
95%
.
Repeat as necessary for other servos.
Close menu.
Where next? Adjust
END POINTs
: see p. 32 and
SUB-TRIMs
: see p. 49.
Set up dual/triple rates and exponential(
D/R
,
EXP
): see p. 42.
Set up
ELEV-FLAP
mix: see p. 62.
View additional model setups on the internet: www.futaba-rc.com\faq\.
58


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Robbe Futaba FF-10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Robbe Futaba FF-10 in the language / languages: English as an attachment in your email.

The manual is 1,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Robbe Futaba FF-10

Robbe Futaba FF-10 User Manual - German - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info