713889

Quickie Life i Manual

20
Zoom out
Zoom in
Previous page
1/96
Next page
ENGLISH
20
Life i Rev.6.0
Castor
Castor, Castor adapter, Castor fork (Fig. 6.20 - 6.20.2)
From time to time the wheelchair may veer slightly to the right or
left or the castors may flutter.
This may be caused by the fol low ing:
Forward and/or reverse wheel motion has not been set properly.
The castor angle has not been adjusted properly.
Castor and/or rear wheel air pressure is incorrect; wheels do not
turn smoothly.
The optimum adjustment of the castors is required so that the
wheelchair runs in a straight line. Casters should always be
adjusted by an authorized dealer.
The castor plates must be re-adjusted, and the wheel locks must
be checked every time the rear wheel position has been altered.
Check the setting of the castor adapter (1) by placing a set-
square next to it and looking at it from the front. Make sure that
the adapter is at right angles to the floor. By undoing the screws
(2) and moving the adapter, you can then re-adjust the wheels to
their optimum position, by adjusting the corresponding teeth
segments. Make sure that after any adjustment work, all screws
are tightened correctly (see the page on torque).
The screws used are fitted with threadlock at the factory and can
be adjusted 5 x after fitting. After that they should be replaced or
alternatively re-secured with threadlock to medium tightness.
Fig. 6.20
90°
2
1
Axle plate
Axle plate (Fig. 6.21)
The position of the centre of gravity in relation to the rear wheel
is an important factor for easy and comfortable driving. Several
positions are possible. If you move the perforated plate to the
rear, the chair is in a safe position, but at the same time is not so
manoeuvrable, as it is when the perforated plate is positioned
further forward.
By moving the axle plate up and down, you can adjust the seat
height of the wheelchair. Make sure that after any adjustment
work, all screws are tightened correctly (see the page on
torque).
CAUTION!
If necessary, the brakes and castors must be re-adjusted.
Fig. 6.21
Cambers
Cambers (Fig. 6.22)
The camber of the chair can be adjusted from 0° to 3°.
Doing this gives increased stability against the wheelchair falling
to the side, and will also improve the wheelchair’s
manoeuvrability.
Loosen the screws on the axle plate and then turn the adapter
by 180̊. Then tighten the screws again (see the page on torque).
Setting the wheel camber increases the overall width of the
wheelchair (each degree adds on approx. 100 mm).
CAUTION!
If necessary, the brakes and castors must be re-adjusted.
Fig. 6.22
Front seat height
To adjust the front seat height, please loosen the screws A (2
on each side) and set to the required seat height. Ensure that
both sides are at the same height and then re-tighten the
screws. Please note the torque required (see the page on
torque).
Fig. 6.20.2
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quickie Life i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quickie Life i in the language / languages: English, Dutch, French, Italian as an attachment in your email.

The manual is 3,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info