713889
18
Zoom out
Zoom in
Previous page
1/96
Next page
ENGLISH
18
Life i Rev.6.0
Step tubes are used by attendants to push a wheelchair over an
obstacle. Simply step on the tube to push a wheel chair, for
example, over a kerb or step, (Fig. 6.5).
CAUTION!
Sunrise Medical strongly reccommends the use of a step tube
on any model where attendant use
is the predominant intended use.
Damage to the backposts may
occur if you constantly use the
backpost without a step tube, as a
lever to pull back on to tip the
wheelchair.
Tipping Tubes
Fig. 6.5
Footplates (Fig. 6.6)
There are two types of footplates:
platform and divided. They can be
flipped up to facilitate getting in and
get ting out of your wheelchair.
Lower leg lengths
By removing the setscrews (1),
the footrest can be adjusted to fit
any lower leg length. Remove
setscrews, set tubing with footrest
in the desired position, and reinsert and tighten the setscrews
(see the page on torque). Make sure that the compo site plastic
pad is in the proper position under the setscrew. A minimum
interval of 25 mm from the ground should always be
maintained.
The screws used are fitted with threadlock at the factory and
can be adjusted 5 x after fitting. After that they should be
replaced or alternatively re-secured with threadlock to medium
tightness.
Footplates
Width Adjustment of Aluminium Footrests
If the footrest width needs to be
adjusted, please undo the screw
(1), set the desired width, by
positioning 1, 2 or 3 spacers (2)
from outer to the inner side and
then refit the screws, (Fig. 6.7):
Angle Adjustment of Aluminium Footboard
The footboard can be flipped up to make it easier to transfer to
and from the chair, (Fig. 6.8 - 6.11).
This can be adjusted to alter the angle to the ground.
Tighten screw (1) on the outside. By loosening the clips (2) the
footboard can be moved to three positions both forwards and
backwards. By adjusting the set screw (3) the footboard can be
changed to a horizontal position. To do this, the footboard must
be flipped up. Make sure that after any adjustment work, all
screws are tightened correctly (see the page on torque). Ensure
that you maintain the minimum gap to the floor (25 mm).
Fig. 6.10
3
Fig. 6.8
1
Fig. 6.9
2
Fig. 6.11
>25 mm
Fig. 6.7
1
Fig. 6.6
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quickie Life i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quickie Life i in the language / languages: English, Dutch, French, Italian as an attachment in your email.

The manual is 3,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info