815528
27
Zoom out
Zoom in
Previous page
1/40
Next page
27 02/237022-802K
D. Igniter
PART NUMBER: SRV7000-462
1. Shut down the appliance by turning down the thermostat
and let the appliance completely cool down. After the
appliance has cooled down, unplug it and remove the
ash drawer.
2. The wire leads to the igniter are connected to the wire
harness with 1/4 inch (6mm) male / female spade
connectors. These wires will pull forward approximately
4 to 5 inches (102mm to 127mm) through the grommet
at the back of the ash drawer chamber. Disconnect
the spade connections and remove the igniter from
the chamber. Loose the thumb screw and slide igniter
out (Figure 27.1).
3. Install new igniter into the chamber and tighten the
thumb screw. Re-connect the wires to the 2 leads with
the spade connectors.
4. Push excess wire leads back through the grommet, one
wire at a time, to take-up the 4 to 5 inches (102mm to
107mm) previously pulled out. This will keep the wires
out of the way of the ash drawer. Double check that the
igniter wires are clear of any movement, i.e. ash drawer,
re pot cleaning rod, cleaning slide plates, etc.
5. Re-install the ash drawer and then re-install the side
panel and re-connect the power.
E. Glass
PART NUMBER: SRV7021-032
1. Open the face and remove door from the appliance
by lifting door off of hinge pin and lay on a at surface
face down.
2. Using a screwdriver, tap the bottom of the rope retainer
rod to push it up out of the hole. The top end of the rod
will slide up. Swing the rod toward you from the bottom
and remove the rod. Repeat for other side.
3. Remove old glass and replace with new glass.
4. Slide the retainer rod into the top hole rst, and then line
up the bottom crimped end with the hole in the door. The
crimped end must be parallel with the glass in order to
insert it into place (Figure 27.2).
Figure 27.1
Igniter
Igniter Bracket
Thumb Screw
Figure 27.2
Screws Rope
Glass Retainers
Glass
Assembly
Door Assembly
Shock Risk.
Do NOT remove grounding prong
from plug.
Plug directly into properly grounded 3
prong receptacle.
Route cord away from appliance.
Do NOT route cord under or in front
of appliance.
CAUTION
Glass is 5mm thick high temperature heat-
resistant ceramic glass.
DO NOT REPLACE with any other material.
Alternate material may shatter and
cause injury.
WARNING
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadra-Fire Castile - Pellet - Insert at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadra-Fire Castile - Pellet - Insert in the language / languages: English as an attachment in your email.

The manual is 9.65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quadra-Fire Castile - Pellet - Insert

Quadra-Fire Castile - Pellet - Insert User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info