815528
28
Zoom out
Zoom in
Previous page
1/40
Next page
28 02/237022-802K
2. Convection Blower: The convection blower is mounted
at the bottom rear of the appliance. There are 2 impellers,
one on each side of the motor. The convection blower
pushes air through the heat exchange system into the
room.
3. Exhaust Blower: The exhaust blower is mounted on the
right side of the appliance behind the right side panel.
The exhaust blower is designed to pull the exhaust from
the appliance and push it out through the venting system.
4. Feed System: The feed system is located behind the
rebox and can be removed as an entire assembly. The
assembly includes the feed motor, mounting bracket,
bearing and feed spring (auger). The hollow feed spring
(auger) pulls pellets up the feed tube from the hopper
area and drops them down the feed chute into the re
pot at a set rate. The feed motor starts and stops every 7
seconds.
5. Fire pot: The re pot is made of high quality ductile iron
and has a cleaning pull-out rod. The oor of the re pot
opens for cleaning when you pull out the rod. Be sure that
the oor returns to a completely closed position or your
appliance will not operate properly.
6. Fuse: The fuse is located on the side of the junction box
near the red call light. The fuse will blow should a short
occur and shut off power to the appliance.
7. Heat Exchangers: The heat exchangers transfer heat
from the exhaust system into convection air. There are 2
clean out rods located under the heat exchangers.
A. Component Functions
1. Control Box
a. The control box is located on lower right side of
appliance, on top of the junction box.
b. There is a light located inside of the control box. The
internal light will turn green when the appliance has
reached a temperature of 200°F (93°C) in the re pot.
and will turn red when it reaches 600°F (315°C).
c. There is also an internal blue light located in the
upper left corner of the control box. When you plug
in the appliance the blue light will automatically start
blinking 6 blinks every 10 seconds for 60 seconds
(depending upon setting) and then will stop.
NOTE: Do NOT open the control box. This will void the
warranty. If you need to plug in or remove the control box
you must rst unplug the appliance.
8. Heat Output Switch: The heat output switch is located
on the lower right side of rebox, behind the front access
door and above the reset button. The function of the heat
output switch is to regulate the burn rates; low, medium
and high settings.
9. Hopper Switch: The hopper switch is located in the
upper right hand corner, outside of the hopper. This
switch is designed to shut down the feed motor whenever
the hopper lid is opened.
10. Igniter: The igniter is mounted on the base of the re pot.
Combustion air travels over the red hot igniter creating
super heated air that ignites the pellets.
11. Junction Box And Wiring Harness: The junction box is
located on the lower right side of the appliance, behind
the left front access door. The junction box and wiring
harness are replaced as one component.
12. Power Supply: The power outlet is located on the lower
right side of the appliance on the front of the junction box.
Check the wall receptacle for 120 volt, 60 Hz (standard
current). Make sure the outlet is grounded and has the
correct polarity. A good surge protector is recommended.
When operating with a generator you need a least 600
watts of power, or with an inverter at least 800 watts of
power available for the appliance during the start cycle.
13. Red Call Light: The red call light is on the top of the
junction box by the fuse. The function of the red call light
is to indicate that the thermostat is calling for heat.
14. Reset Button: The reset button is located on the lower
right side of rebox in behind the access door and below
the heat output control switch. The function of the switch
is to momentarily open the thermostat circuit, which
restarts the system.
15. Thermocouple: The thermocouple is located on
top of the re pot inside the thermocouple cover
(ceramic protection tube). The thermocouple sends a
millivolt signal to the control box indicating the preset
temperatures of the green and red lights have been
obtained.
16. Thermostat: The appliance is designed to run on a
5 volt DC thermostat. The heat anticipator, if present,
should be set on the lowest setting available.
When describing the location of a
component, it is always AS YOU FACE
THE FRONT OF THE APPLIANCE.
6 6 reference Materials
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Quadra-Fire Castile - Pellet - Insert at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Quadra-Fire Castile - Pellet - Insert in the language / languages: English as an attachment in your email.

The manual is 9.65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Quadra-Fire Castile - Pellet - Insert

Quadra-Fire Castile - Pellet - Insert User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info