490702
18
Zoom out
Zoom in
Previous page
1/134
Next page
18
gentially-exiting connector [3-4], into which
the 27 mm dia. suction hose can be inserted
[3-5]. If the machine is used without a dust
extractor, the chip de ector [3-6] should
in all cases be tted to the connector. The
direction in which the chips y can be varied
by turning the chip de ector. During opera-
tion with a suction hose, the chip de ector
is inserted into the adjusting nob [3-11] at
the left-hand end of the platen [1-7].
7.7 Replacing the Saw Blade
WARNING
Before exchanging the saw blade, pull
the mains plug from the power sup-
ply socket.
Wear protective gloves!
The spindle locking button [3-1] may
be pressed only when the saw blade
is at a standstill.
Removing the saw blade
Swing back the protective guide [2-7] with
the lever [1-9].
Depress the spindle locking button [3-1].
Unscrew the clamping screw [2-4] with the
Allen key from motor spindle.
Remove the clamping ange [2-5] and the
saw blade [2-6].
Saw blade installation
The sawing performance and the quality of
the cut depend essentially on the condition
and tooth form of the saw blade. Therefore,
use only sharp saw blades that are suitable
for the material to be worked.
Swing back the swinging guard [2-7] with
the lever [1-9].
Depress the spindle locking button [3-1].
Install a suitable saw blade according to the
illustration and tighten. Take care that the
mounting ange and the clamping ange
are correctly positioned.
WARNING
Observe for installation: The cutting
direction of the teeth (arrow on the
saw blade) must match the direction
of the arrow on the guard.
Check the function of the swinging
guard.
8 Operating Instructions
Do not cut into nails, screws, etc.
Do not work with materials containing
asbestos.
Do not use saw blades that have cracks
or that are damaged.
Under no circumstances use abrasive
disks!
Saw blades of highly alloyed, high-speed
steel (HSS-steel) must not be used.
Feeding too fast signi cantly reduces the
performance of the machine and short-
ens the life of the saw blade.
Use only sharp saw blades in perfect con-
dition.
Uncoated saw blades can be protected
from corrosion with a thin coat of acid-
free oil.
Resin and glue on the saw blade cause
poor cutting results. Therefore, clean the
saw blade immediately after use.
Working different materials
Wood
The proper selection of the saw blade is
dependent on the type and quality of the
wood as well as whether the wood is to be
sawed along or across the grain.
Beech and oak dust is especially detrimental
to health and therefore should be worked
only with vacuum dust extraction.
Plastic
When cutting plastic, especially PVC, long,
spiral shaped shavings are produced that
can be electrostatically charged.
This can cause the ejector to become clogged
and the swinging protective guard [2-7] to
stick. The use of a vacuum cleaner for dust
extraction is recommended.
Apply the machine running against the work-
piece and carefully start sawing. Then saw
steadily and without interruption so that the
saw teeth have less chance of sticking.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Protool CSP85-45 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Protool CSP85-45 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info