490702

Protool CSP85-45 Manual

16
Zoom out
Zoom in
Previous page
1/134
Next page
16
f) Adjust the riving knife as described
in the operating instructions. Incor-
rect width, position and alignment can be
the cause that the riving knife does not
effectively prevent kickback.
g) Always use the riving knife, except
when performing plunge cuts. After the
plunge cut, mount the riving knife again.
The riving knife interferes when performing
plunge cuts and can lead to kickback.
h) In order for the riving knife to be ef-
fective, it must be located in the cut.
For short cuts, the riving knife is ineffec-
tive for the prevention of kickback.
i) Do not operate the saw with a bent
riving knife. Even a minor malfunction
can lead to sluggish retraction of the re-
tracting blade guard.
5.5 Noise/Vibration Information
Measured values determined according to
EN 60 745.
Typically the A-weighted noise levels of the
tool are:
Sound pressure level: 92 dB (A).
Sound power level: 103 dB (A).
Inaccuracy of measurement K = 3 dB (A).
CAUTION
The noise created during work may
damage hearing.
► Use hearing-protective aids!
The typical hand-arm vibration is below
2.5 m/s
2
.
Inaccuracy of measurement K = 1.5 m/s
2
.
6 Commissioning and
Operation
WARNING
Risk of injury, if the tools are used
with wrong supply power.
The voltage specifi cations on the rating plate
must correspond with the mains voltage.
Equipment marked with 230 V can also be
connected to 220 V / 240 V.
Check that the plug type is the same as the
socket type.
Adjustment of the riving knife
WARNING
Risk of injury, if the riving knife is not
correctly adjusted.
The riving knife [2-8] must always be used
for safety reasons. The riving knife prevents
the saw blade from becoming jammed when
making lengthwise cuts.
Loosen screw [2-9], adjust the riving knife
[2-8] and retighten the screw (see fi gure).
2-9
2-8
2.5 – 5 mm
2.5 – 5 mm
Check the function of the swinging guard
[2-7].
Switching On/Off
Switching On:
Press the safety button [1-1].
Press the on-off switch and hold depressed.
Note: The on-off switch cannot be locked on.
Switching Off:
Release the on-off switch [1-2].
7 Adjustment
WARNING
Risk of electric injury.
► Before any manipulation with the tool
make sure to unplug the mains socket
outlet.
7.1 Electronic Motor Control
Starting current limiting
The electronically controlled smooth start
takes care that the machine starts without
jerk. As a result of the machine’s reduced
starting current, a 16 A fuse is suffi cient.
No-load speed reduction
The electronic control reduces the no-load
speed of the machine which results in re-
duced noise and wear of motor and gear.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Protool CSP85-45 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Protool CSP85-45 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info