Manual Protool CSP85-45 (page 17 of 134) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

490702

Zoom out

Zoom in

1/134

Constant speed electronics

The constant speed electronics maintains

the speed between no load and load nearly

constant and ensures uniform feeding which

produces an even cutting edge.

Electronic overload protection

In case that the machine is extremely over-

loaded, an electronic overload protection

protects the motor from damage. In this

case, the motor stops and restarts only af-

ter the feeding pressure is reduced, res.

after relief.

Temperature-dependent overload

protection

To protect the motor from overheating at

extreme permanent load, it is switched off

by the protective electronic system when

a critical temperature is reached.

After a cooling-down period of approx.

3 – 5 min., the machine is again ready for

use and can be fully loaded.

When the machine is warmed by use, the

temperaturedependent overload protection

reacts earlier as a result.

LED indicators

The green LED [1-6] shows the operator

that the machine is running. The red LED

[1-5] indicates that the motor is overloaded

to approx. 70 %. If the motor is subject to

an overload of this kind for a lengthy pe-

riod, it will be switched off by the overload

protection device.

► If the red LED lights, reduce the feed

force until this red LED goes out again.

The machine is then operating in the per-

missible overload range.

Speed pre-selection

With the speed control [1-4], the speed can

be continuously pre-selected:

Speed 1: 1500 min

–1

Speed 4: 2400 min

–1

Speed 2: 1700 min

–1

Speed 5: 2700 min

–1

Speed 3: 2100 min

–1

Speed 6: 3000 min

–1

The required speed depends on the saw blade

used and the material to be worked.

Run-on Brake

After releasing the On/Off switch, the in-

tegrated run-on brake stops the saw blade

within approx. 2 seconds.

7.2 Cutting Depth Adjustment

Loosen the clamping lever [3-9].

Set the required depth on the cutting depth

scale [3-3].

Re-tighten the clamping lever [3-9].

To achieve the best cutting results, the saw

blade should protrude from the material by

no more than 3 mm.

7.3 Cutting Angle Adjustment

Loosen the winged screws [2-10, 1-11].

Set the cutting depth on the scale [3-7] to

the required value (the cutting angle scale

is marked in 1°-steps).

Re-tighten the winged screws [2-10, 1-11].

The pivot point of the circular hand saws

lies at the point of intersection of the con-

tact level of the guide rail [A] and the cut-

ting edge [B] – ﬁ gure [5].

WARNING

The maximum cutting depth is reduced

for bevel cuts.

7.4 Cutting Edge Indicator

The cut of the saw blade can be seen on

the cutting edge [1-12] on the front of the

saw table. The cutting edge situated behind

the indicator is valid at the tilt of the saw

to 45° (without the guiding rail).

7.5 Parallel Guide

The parallel guide can be used up to the

width of the cut 180 mm. The bar of the

ruler is inserted into the saw’s slide guide

[2-3] and after setting the required width of

the cut, it is then tightened using the hand

screw with the set backstop.

7.6 Exhaustion

CAUTION

Inhaled dust may damage the air pas-

sages.

► Tools should be permanently connected

to the dust exhausting plant.

► Wear respirator if you work with dust.

When working in enclosed areas, the cir-

cular hand saw should be connected to an

extraction system. For this purpose, the cir-

cular hand saws are equipped with a tan-

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protool CSP85-45 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protool CSP85-45 Manual

Product: