Manual Protool CSP85-45 (page 19 of 134) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

490702

Zoom out

Zoom in

1/134

Non-ferrous Metals

Use only a suitable and sharp saw blade.

This ensures a clean cut and prevents jam-

ming of the saw blade.

Apply the machine running to the workpiece,

carefully start sawing and then saw with

slow feeding and without interruption.

For proﬁ les, always start the cut on the small

side; for U-proﬁ les, never start the cuts on

the open side.

Support long proﬁ le, otherwise the saw

blade can become jammed when the proﬁ le

tips over and the machine can “kick back”.

Connect the circular saw through a circuit

breaker to current protection (FI).

Connect suitable vacuum cleaner to the

tool.

Keep the tool clean off dust which accumu-

lates on the engine housing and inside the

protective cover.

Safety goggles should always be worn.

When large panels are cut, parafﬁ n should

be used as a lubricant. Thin-walled proﬁ le

sections upto 3 mm thick can be cut without

lubrication.

Material with Mineral Content

(Light building material)

► Only dry cutting is permitted.

► Use vacuum dust extraction. The vacu-

um cleaner must be suitable for masonry

dust.

9 Use of Accessories

The machine has a longitudinal slot at the

base plate underside to take up a guide rail.

With this guide rail, it is made easy to carry

out larger cuts.

PROTOOL Guiding System

For easy and safe handling when cutting

large work pieces as well as for achiev-

ing exact angle cuts, the use of the

GRP 800/1400/3000-2 guiding system is

recommended.

With it, clean cuts are possible by preci-

sion guiding of the machine along a cutting

line. In addition, the hard anodising of the

guide rail makes possible easy gliding of the

machine and thereby reduces the required

advancing force while improving the work

progress.

The guide rails are equipped with a splinter-

guard [4-1], which has to be cut to size

before the ﬁ rst use:

- Set the speed of the machine to level 6,

- Place the machine on the rear end of the

guide rail,

- Switch the machine on, press it down to

the set cutting depth and cut the splinter-

guard along the full length without inter-

ruption. The edge of the splinterguard

now corresponds exactly to the cutting

edge.

The saw’s side suction clearance is possible

to adjusting the adjusting nobs [3-11].

Mounting the Guide Rail

(GRP 800/1400/3000-2)

The mounting of the guide rail takes place

with the use of the special screw clamps

CL-GRP 300 [4-2] which are slid into the re-

ceptacle slots provided. This makes secure

holding possible also on uneven surfaces.

In addition, the “Anti-slip Coating” applied

to the underside of the guide rail ensures

secure contact and prevents scratches on

sensitive material surfaces.

Mounting the Connection Piece

(CN-GRP)

Depending on the application and the size

of the work piece, several guide rails can

be connected together with the use of the

connection piece. For the permanent con-

nection of several guide rails, the connec-

tion pieces can be fastened with screws at

the respective threaded holes.

Mounting the Angle Unit (GRP-AG-2)

The combination of the guide rail and the

continuously adjustable angle unit makes

possible exact angle cutting, e. g., for ﬁ t-

ting work. On the scale, the required angle

can be set.

► When sawing with the PROTOOL GRP

guiding system, 4.5 mm is always to be

added to the necessary cutting depth.

Saw Table

Additional application possibilities are avail-

able with the use of a saw table. Further

information in this regard is available from

your dealer.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Protool CSP85-45 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Protool CSP85-45 Manual

Product: