708084
12
Zoom out
Zoom in
Previous page
1/18
Next page
17
40. Locate the Low Cable (82). Route the eyelet
end of the Cable through the Center Upright (37)
a
nd under a 90mm Pulley (90). Attach the Pulley
inside the Upright with an M10 x 75mm Bolt
(
127), two M10 Washers (99), two 17mm Spacers
(86), and an M10 Nylon Locknut (97).
41. Route the Low Cable (82) over a 90mm Pulley
(90) as shown. Attach the Pulley and two Half
Finger Guards (133) to the Double ā€œUā€-bracket
(73) with an M10 x 47mm Bolt (136) and an M10
Nylon Locknut (97).
42. Route the Low Cable (82) under a 90mm Pulley
(90) as shown. Attach the Pulley and two Half
Finger Guards (133) to the Rear Base (33) with
an M10 x 47mm Bolt (136) and an M10 Nylon
Locknut (97).
43.
Route the Low Cable (82) over a 90mm Pulley
(90) as shown.
Attach the Pulley
, a Small Cable
Trap (125), and two Half Finger Guards (133) to
the second set of holes from the bottom of the
two Pulley Plates (72) with an M10 x 47mm Bolt
(136) and an M10 Nylon Locknut (97). Make sure
the Cable Trap is oriented to hold the Cable in
the groove of the Pulley
.
40
82
37
97
99
99
127
90
86
86
97
73
136
133
133
90
82
41
97
90
82
33
97
90
125
82
72
136
133
133
42
43
24. Attach the Center Upright (37) to the Center Base
(32) and Rear Base (33) with an M10 x 78mm
Bolt (110), an M10 Washer (99), and an M10
Nylon Locknut (97). Do not tighten the Locknut
yet.
Attach the Center Upright (37) to the Center Base
(32) with an M10 x 75mm Bolt (127), two M10
Washers (99), and an M10 Nylon Locknut (97).
Do not tighten the Locknut yet.
Attach a Weight Carriage Stop (70) to the Rear
Upright (38), at the indicated hole, with an M10 x
88mm Bolt (114) and an M10 Nylon Locknut (97).
Make sure the Square Carriage Bushing (61)
is on top.
Attach the Rear Upright (38), with the hexagonal
holes on the indicated side, to the Rear Base (33)
with two M10 x 75mm Bolts (127), four M10
Washers (99), and two M10 Nylon Locknuts (97).
Do not tighten the Locknuts yet.
12
Hexagonal
Holes
24
110
37
38
97
97
33
32
99
99
127
114
61
127
Hole
99
99
70
97
97
55
59
120
23. Slide the Barbell Adapter (59) onto the Weight
Bar (55). Thread a 1/4ā€ x 9.5mm Allen Head Set
S
crew (120) into the Barbell Adapter. D
o not
tighten the Screw yet.
Repeat this step with the other Barbell
Adapter (not shown).
23
136
133
133
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pro-form G880 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pro-form G880 in the language / languages: English as an attachment in your email.

The manual is 4,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pro-form G880

Pro-form G880 User Manual - German - 18 pages

Pro-form G880 User Manual - Dutch - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info