708084
13
Zoom out
Zoom in
Previous page
1/18
Next page
16
35. Locate the Lat Cable (81). Route the Cable up
through the Rear Top Frame (39) and over a
9
0mm Pulley (90). Attach the Pulley inside the
Rear Top Frame with an M10 x 78mm Bolt (110),
t
wo M10 Washers (99), two 17mm Spacers (86),
and an M10 Nylon Locknut (97).
36. Route the Lat Cable (81) over a 90mm Pulley
(90) and down through the Rear Top Frame (39).
Attach the Pulley inside the Rear Top Frame with
an M10 x 78mm Bolt (110), two M10 Washers
(99), two 17mm Spacers (86), and an M10 Nylon
Locknut (97).
37. Wrap the Lat Cable (81) under a 90mm Pulley
(90). Attach the Pulley, a Small Cable Trap (125),
and two Half Finger Guards (133) to the indicated
hole in the two Pulley Plates (72) with an M10 x
47mm Bolt (136) and an M10 Nylon Locknut (97).
Make sure the Cable Trap is turned to hold the
Cable in the groove of the Pulley.
38. Wrap the Lat Cable (81) over a 90mm Pulley
(90).
Attach the Pulley inside the Rear Top Frame
(39) with an M10 x 78mm Bolt (110) and an M10
Nylon Locknut (97).
39.
Attach the Lat Cable (81) to the M10 x 19mm Hex
Head Bolt (132) in the Weight Carriage (71) with
an M10 Nylon Locknut (97). Do not overtighten
the Locknut; the Cable must be able to pivot.
35
90
81
3
9
86
86
99
99
97
110
36
90
81
39
86
86
99
99
97
110
37
38
39
97
81
72
72
90
136
133
133
125
90
110
81
97
39
81
71
97
132
25. Insert an M10 x 19mm Hex Head Bolt (132) into
the bracket on the Weight Carriage (71) from the
s
ide shown.
O
rient the Weight Carriage (71) as shown and
slide it onto the Rear Upright (38).
Attach the Weight Carriage Stop (70) to the Rear
Upright (38), at the indicated hole, with an M10 x
88mm Bolt (114) and an M10 Nylon Locknut (97).
Make sure the Square Carriage Bushing (61)
is on the bottom.
27. Attach the Rear Top Frame (39) to the Center
Upright (37) with two M10 x 78mm Bolts (110),
two M10 Washers (99), and two M10 Nylon
Locknuts (97).
Do not tighten the Locknuts yet.
Attach the Rear Top Frame (39) to the Top Frame
(40) with two M10 x 127mm Bolts (126), four M10
Washers (99), and two M10 Nylon Locknuts (97).
Do not tighten the Locknuts yet.
26. Attach the Rear Top Frame (39) to the Rear
Upright (38) with two M10 x 72mm Hex Head
Bolts (130), two M10 Washers (99), and two M10
Nylon Locknuts (97). Make sure the bolt heads
are set inside the hex holes in the Rear
Upright. Do not tighten the Locknuts yet.
13
25
97
6
1
7
1
38
132
70
114
26
99
97
99
38
39
130
Hole
27
99
99
99
99
97
97
37
40
97
39
126
110
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pro-form G880 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pro-form G880 in the language / languages: English as an attachment in your email.

The manual is 4,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pro-form G880

Pro-form G880 User Manual - German - 18 pages

Pro-form G880 User Manual - Dutch - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info