708084
11
Zoom out
Zoom in
Previous page
1/18
Next page
20
21
22
18
44. Attach the Low Cable (82) inside the Rear Base
(33) with an M10 x 75mm Bolt (127), two M10
W
ashers (99), two 27mm Spacers (87), and an
M10 Nylon Locknut (97).
Do not overtighten the
L
ocknut; the Cable must be able to pivot easily.
45. Attach the Butterfly Backrest (80) to the Center
Upright (37) with two M6 x 72mm Screws (105)
and two M6 Washers (101).
46. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in
ADJUSTMENTS, beginning on the following page.
Before using the weight bench, pull each cable a few times to make sure that the cables move smoothly
over the pulleys. If one of the cables does not move smoothly
, find and correct the problem.
IMPORT
ANT: If
the cables are not properly installed, they may be damaged when heavy weight is used. See the
CABLE DIAGRAMS on page 22 of this manual for proper cable routing. If there is any slack in the
cables, you will need to remove it by tightening the cables. See TROUBLESHOOTING on page 23.
44
45
97
8
7
87
99
99
82
3
3
127
80
37
101
101
19. Press a Round Joint Bushing (74) into the Left
Frame Joint (49).
Orient the Top Frame (40) with the name decal in
t
he indicated position. Attach the Top Frame to
the Left Frame Joint (49) with two M10 x 91mm
Bolts (116), four M10 Washers (99), and two M10
Nylon Locknuts (97). Do not tighten the
Locknuts yet.
Assemble the Right Frame Joint (50) to the
Top Frame (40) in the same manner.
11
19
40
Decal
97
116
99
99
49
74
50
105
105
20. Attach the Left Frame Joint (49) to the Left
Upright (36) with two M10 x 91mm Bolts (116),
four M10 Washers (99), and two M10 Nylon
Locknuts (97).
Do not tighten the Locknuts yet.
Attach the Left Frame Joint (49) to the Guide Bar
(41) with an M10 x 50mm Screw (108) and an
M10 Washer (99).
Assemble the Right Frame Joint (50) in the
same manner.
21. Slide the Weight Bar (55) through the Left Barbell
Glider (51), the Locking Bar (56), and the Right
Barbell Glider (123). Make sure the Locking Bar
is oriented as shown.
Engage the hooks on the Locking Bar (56) into a
set of holes in the Uprights (36, 69).
99
56
36
69
123
51
55
41
116
36
97
108
99
99
49
22.
Slide a Weight Stop (67) onto the Weight Bar
(55). Thread a 1/4” x 14mm Screw (119) into the
Weight Stop and the hole in the Weight Bar.
Do
not tighten the Screws.
Thread a 1/4” x 14mm Screw (119) into the Left
Barbell Glider (51). Do not tighten the Screws.
Repeat this step with the Right Barbell Glider
(not shown) and the other Weight Stop (not
shown).
55
51
119
119
67
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Pro-form G880 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Pro-form G880 in the language / languages: English as an attachment in your email.

The manual is 4,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Pro-form G880

Pro-form G880 User Manual - German - 18 pages

Pro-form G880 User Manual - Dutch - 18 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info