582667
8
Zoom out
Zoom in
Previous page
1/14
Next page
POWX1365MB EN
Copyright © 2015 VARO P a g e | 8 www.varo.com
Switch on the laser generator (1) from the laser aperture using the laser generator switch
(2).
Align the beam with the mark on the work-piece and slowly push the saw forward using
both hands, keeping the red light beam on the mark.
Switch off the laser beam when completion of the cut.
9.4 Line following
A V-shaped pointer and pointer locate at the front and the rear position of the base plate (18)
which allow a line to be followed, when cutting. (Refer to Fig. 6)
9.5 Dust extraction
The circular saw is a powerful tool capable of producing a large amount of dust. As the tool
has a fully enclosed blade, forced dust extraction is particularly efficient. Forced dust
extraction should be used for all but small trimming jobs.
Push the dust extraction hose (b) on to the dust extraction nozzle (17).
Connect a vacuum device approved for the extraction of sawdust and splinters to the dust
extraction hose (b).
10 CUTTING
WARNING! Before using the machine, need to check the function of tiltable
protective cover (12) can be used properly.
WARNING: Always cut in a forward direction. Never draw the tool
backwards. If you are a novice user, practice by cutting thin wood until
proficient.
Check the specifications to ensure the suitability of the material to be cut.
Fit the correct blade ensuring it is sharp and not damaged.
Set the depth of cut. (See Setting the cutting depth section)
Place the material to be cut onto a flat surface such as a workbench, table or floor. Use a
piece of scrap material underneath if:
You do not wish to damage the work surface.
The work surface is likely to damage the blade. E.g. a concrete floor.
Plug into mains supply.
Grasp the tool firmly (See Holding & switching ON/OFF section) and rest its metal
base plate onto the surface to be cut. Ensure that the rear half of the base plate
overhangs the work surface. Do not plunge the blade into the material.
Switch on the tool and wait for a moment for the blade to run up to speed. Next, depress
the safety lock button (3) and plunge the blade into the material slowly and gently, but
firmly. Then push the tool forwards along the line to be cut. If necessary, switch on the
laser generator (1).
NOTE: Never draw the tool backwards.
Very little force should be used to feed the tool along the cut. Excess force will cause
operator fatigue and excessive wear to the blade and tool. Excess force is also likely to
cause the temperature cut-out to trip, resulting in delays.
Ensure that the base plate is always held flat on the material being cut. This is particularly
important at the start or finish of a cut or if thin strips are being cut where the base plate is
not fully supported.
Once the cut has been finished, lift the tool from the work surface before switching off. If a
lot of dust has been created, keep switched on for a few seconds extra to allow the dust to
clear from within the tool.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX1365MB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX1365MB in the language / languages: English as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX1365MB

Powerplus POWX1365MB User Manual - German - 15 pages

Powerplus POWX1365MB User Manual - Dutch - 15 pages

Powerplus POWX1365MB User Manual - French - 15 pages

Powerplus POWX1365MB Additional guide - All languages - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info