481033

Powerplus POWX0761 Manual

11
Zoom out
Zoom in
Previous page
1/24
Next page
POWX0761 EN
Copyright © 2008 VARO P a g e | 11 www.varo.com
8.2 Maintaining maximum cutting capacity (Fig. 7)
This tool is factory adjusted to provide the maximum cutting capacity for a 255 mm saw blade.
When installing a new blade, always check the lower limit position of the blade and if
necessary, adjust it as follows:
CAUTION:
When making this adjustment, unplug the tool.
First, unplug the tool. Lower the handle completely. Use the wrench to turn the adjusting bolt
until the periphery of the blade extends slightly below the top surface of the turn table at the
point where the front face of the guide fence meets the top surface of the turn table. With the
tool unplugged, rotate the blade by hand while holding the handle all the way down to be sure
that the blade does not contact any part of the lower base. Readjust slightly, if necessary.
CAUTION:
After installing a new blade, always be sure that the blade does not contact any part of the
lower base when the handle is lowered completely. Always do this with the tool unplugged.
This tool can be used with or without the lower limit by shifting the lower limit stopper as
shown in the figure. (Fig. 8 - 15)
To use the tool without the lower limit, turn the stopper end counterclockwise. Use in this
position is proper to cut a wide and thin workpiece.
To use the tool with the lower limit, move the stopper end clockwise. Use in this position is
proper to cut a thick workpiece.
8.3 Adjusting the Mitre angle (Fig. 9 & 10)
Loosen the clamping screw on the guide fence by turning counterclockwise. Turn the turn
table by handle. When you have moved the handle to the position where the pointer points to
the desired angle on the Mitre scale, securely tighten the clamping screw clockwise.
CAUTION:
When turning the turn table, be sure to raise the handle fully.
After changing the Mitre angle, always secure the turn table by tightening the clamping
screw firmly.
8.4 Adjusting the bevel angle (Fig. 11 & 12)
8.4.1 In the Mitre saw mode
To adjust the bevel angle, loosen the lever at the rear of the tool counterclockwise. Push the
handle to the left to tilt the saw blade until the pointer points to the desired angle on the bevel
scale. Then tighten the lever clockwise firmly to secure the arm.
CAUTION:
When tilting the saw blade, be sure to raise the handle fully.
After changing the bevel angle, always secure the arm by tightening the lever clockwise.
8.4.2 In the table saw mode (Fig. 13)
To adjust the bevel angle, loosen the lever under the table at the front of the tool
counterclockwise. Move the depth adjusting knob to the left to tilt the saw blade until the
pointer points to the desired angle on the bevel scale. Then tighten the lever clockwise firmly
to secure the arm.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0761 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0761 in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0761

Powerplus POWX0761 User Manual - German - 29 pages

Powerplus POWX0761 User Manual - Dutch - 28 pages

Powerplus POWX0761 User Manual - French - 28 pages

Powerplus POWX0761 Additional guide - All languages - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info