481033
12
Zoom out
Zoom in
Previous page
1/24
Next page
POWX0761 EN
Copyright © 2008 VARO P a g e | 12 www.varo.com
8.5 Switch action (Fig. 14)
8.5.1 Switch for the Mitre saw mode (A)
CAUTION:
Before plugging in the tool, always check to see that the switch lever actuates properly and
returns to the “OFF” position when released.
When not using the tool, remove the lock-off button and store it in a secure place. This
prevents unauthorized operation.
Do not pull the switch lever hard without pressing in the lock-off button. This can cause
switch breakage. To prevent the switch lever from being accidentally pulled, a lock-off
button is provided. To start the tool, push the lock lever to the left, press in the lock-off
button and then pull the switch lever. Release the switch lever to stop.
8.5.2 Switch for the table saw mode (B)
CAUTION:
Before operation, make sure that the tool is turned on and off.
To start the tool, press the ON ( I ) button. To stop it, press the OFF (O) button.
8.6 Adjusting the depth of cut (Fig. 15 - 21)
( In the table saw mode )
The depth of cut can be adjusted by turning the cutting depth adjusting knob. Turn the cutting
depth adjusting knob clockwise to raise the blade or counterclockwise to lower it.
WARNING: Use a shallow depth setting when cutting thin materials in order
to obtain a cleaner cut.
CAUTION:
The stopper pin cannot be turned with the tool head at fully lowered position. At this time,
turn the knob counterclockwise slightly and the stopper pin can be released. (Fig. 16)
9 ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and unplugged before carrying out any work on
the tool.
9.1 Socket wrench storage (Fig. 17)
The socket wrench is stored as shown in the figure. When using the socket wrench, pull it out
of the wrench holder. After using the socket wrench, return it to the wrench holder.
9.2 Table height two-way set up
The table height can be set up in two ways, high or low table.
WARNING: Before falling down the tool backwards, always set the tool in
the Mitre saw mode and lock the tool head in the lowest position.
9.2.1 High table set up (Fig. 18)
To set up the tool with high table, proceed as follows.
Fall down the tool carefully BACKWARDS without fail while holding it with both hands.
Fix the 4 legs using a bolt, wing nut and the U-shaped customized washer.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0761 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0761 in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0761

Powerplus POWX0761 User Manual - German - 29 pages

Powerplus POWX0761 User Manual - Dutch - 28 pages

Powerplus POWX0761 User Manual - French - 28 pages

Powerplus POWX0761 Additional guide - All languages - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info