481033
13
Zoom out
Zoom in
Previous page
1/24
Next page
POWX0761 EN
Copyright © 2008 VARO P a g e | 13 www.varo.com
9.2.2 Low table set up (Fig. 19)
Fold in the 4 legs. To do so :
Fall down the tool carefully BACKWARDS without fail while holding it with both hands.
untighten the wing nut of each leg seperatly until you can turn the leg 90° , aligned with
tabel. Then tigthen the wing nut again
Return the tool to the upright position.
9.3 Installing or removing saw blade
CAUTION:
Always be sure that the tool is switched off and unplugged before installing or removing the
blade.
Use only the socket wrench provided to install or remove the blade. Failure to do so may
result in overtightening or insufficient tightening of the hex bolt. This could cause an injury.
Move up the handle in the fully raised position. Press the shaft lock to lock the spindle, use
the socket wrench to loosen the hex bolt clockwise. (Fig. 20) Raise the blade guard A with
its lifting lever while pushing the lever nearby the handle to the left. With the blade guard A
raised, remove the hex bolt, outer flange and blade. (Fig. 21) To install the blade, mount it
carefully onto the spindle, making sure that the direction of the arrow on the surface of the
blade matches the direction of the arrow on the blade case. Install the outer flange and hex
bolt, and then use the socket wrench to tighten the hex bolt (lefthanded) securely
counterclockwise while pressing the shaft lock.
NOTE: When installing a saw blade, be sure to insert it between the blade
guard (7) at first and then raise it so that the blade is finally placed in the
blade guard. (Fig. 22 & 23)
CAUTION:
The ring 30 mm in outer diameter is factory-installed between the inner and outer flanges.
Return the lower blade guard (8) to its original position. Lower the handle to make sure that
the lower blade guards move properly. Make sure shaft lock has released spindle before
making cut.
9.4 Adjusting riving knife (fig 25,26 & 27)
There must be a clearance of about 5 6 mm between the riving knife and the blade teeth
when pushing riving knife toward the blade fully. Adjust the riving knife accordingly by first
loosening clamping nut by hand counterclockwise and then loosening hex bolt
counterclockwise with the hex socket wrench, and measuring the distance. After adjustment,
securely tighten the hex bolt and then the clamping nut clockwise. Always check to see that
the riving knife is secured and that the top blade guard works smoothly before cutting.
The riving knife has been installed before shipment from the factory so that the blade and
riving knife are in a straight line after your simple set-up. Refer to the section titled
“Repositioning riving knife” for the set-up.
CAUTION:
If the blade and riving knife are not aligned properly, a dangerous pinching condition may
result during operation. Make sure the riving knife is positioned between both outer ends of
the blade teeth when viewing from the top. You could suffer serious personal injury while
using the tool without a properly aligned riving knife. If they are not aligned for any reasons,
always have an authorized service center repair it.
When adjusting the riving knife clearance from the blade teeth, always loosen the hex bolt
only after loosening the clamping nut.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0761 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0761 in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0761

Powerplus POWX0761 User Manual - German - 29 pages

Powerplus POWX0761 User Manual - Dutch - 28 pages

Powerplus POWX0761 User Manual - French - 28 pages

Powerplus POWX0761 Additional guide - All languages - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info