481033
9
Zoom out
Zoom in
Previous page
1/24
Next page
POWX0761 EN
Copyright © 2008 VARO P a g e | 9 www.varo.com
6.3 When using in the table saw (bench saw) mode:
Do not perform any operation freehand. Freehand means using your hands to support or
guide the workpiece, in lieu of (6) rip fence.
Make sure that the turn table is fixed securely.
Make sure that the arm is securely fixed in the working position. Tighten the lever clockwise
to fix the arm.
Use (6) push stick or (6) push block to avoid working with the hands and fingers close to the
saw blade.
Make sure the blade is not contacting the riving knife or workpiece before the switch is
turned on.
Always store the push-stick when it is not in use.
Pay particular attention to instructions for reducing risk of KICKBACK. KICKBACK is (6)
sudden reaction to (6) pinched, bound or misaligned saw blade. KICKBACK causes the
ejection of the workpiece from the tool back towards the operator. KICKBACKS CAN LEAD
TO SERIOUS PERSONAL INJURY. Avoid KICKBACKS by keeping the blade sharp, by
keeping the rip fence parallel to the blade, by keeping the riving knife and blade guard in
place and operating properly, by not releasing the workpiece until you have pushed it all the
way past the blade, and by not ripping (6) workpiece that is twisted or warped or does not
have (6) straight edge to guide along the fence.
Avoid abrupt, fast feeding. Feed as slowly as possible when cutting hard workpieces. Do
not bend or twist workpiece while feeding. If you stall or jam the blade in the workpiece, turn
the tool off immediately. Unplug the tool. Then clear the jam.
Before turning over the tool, always make sure that the stopper pin has securely locked the
tool head in the lowest position.
7 INSTALLATION
CAUTION: Keep the floor area around the tool level, well maintained and
free of loose materials e.g. chips and cut-offs.
7.1 Bench mounting (Fig. 1 & 3)
7.1.1 For the fully-extended feet set up as the high table.
When the tool cannot be set up stable, turn the adjusting nut at the foot of the tool for proper
stability. Turn counterclockwise in top viewing to make the foot shorter and clockwise in top
viewing to make it longer. After adjustment, make sure that the tool keep stable.
7.1.2 For the folded feet set up as the low table
When the tool is ready in the foot-folded position, secure the tool by using U-shaped grooves
shown in the figure. (fig 3 (5) )
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0761 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0761 in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0761

Powerplus POWX0761 User Manual - German - 29 pages

Powerplus POWX0761 User Manual - Dutch - 28 pages

Powerplus POWX0761 User Manual - French - 28 pages

Powerplus POWX0761 Additional guide - All languages - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info