677891

Powerplus POWX0760 Manual

16
Zoom out
Zoom in
Previous page
1/23
Next page
POWX0760 EN
Copyright © 2014 VARO NV P a g e | 16 www.varo.com
CAUTION:
After installing the top blade guard, make sure that it works smoothly.
9.10 Setting up the tool in Mitre saw mode (Fig. 50)
WARNING: Be sure to install the lower blade guard C before using the tool
in Mitre saw mode.
To change the set up from table saw mode to Mitre saw mode, reverse the procedure of the
section titled “Setting up the tool in table saw mode”.
9.10.1 Removing the top blade guard
Push the push button of the top blade guard to its side surface and then just take away the top
blade guard upward with the button depressed.
9.10.2 Installing the lower blade guard C
Place the lower blade guard C on the table so that it fits in the slot of the table and tightening
the clamping screw firmly.
9.10.3 Turning over the tool
Refer to the same titled section in the “Setting up the tool in table saw mode”.
9.10.4 Releasing the tool head from fully lowered position
While holding the handle, pull the stopper pin in the direction of arrow A, turn it to the angle of
90° in the direction of arrow B with the stopper pin pulled and then raise the handle slowly.
9.10.5 Repositioning riving knife (Fig. 51)
The position of riving knife (Fig. 51-A) should be changed as follows.
(1) Loosen the clamping nut and hold the lower blade guard A using its lug by hand. (Fig. 51-B)
(2) While holding the lower blade guard A, pull the riving knife so that it turns and pivot it to the
position in the direction of arrow. (Fig. 51-C)
(3) With the riving knife held in that position, return the lower blade guard A to the original
position and tighten the clamping nut securely. (Fig. 51-D & E)
9.10.6 Installing or removing the sub fences R and L (Fig. 52)
CAUTION:
When cutting a workpiece over 20 mm thick, make sure that the sub fences R and L are
securely installed with a screw.
Removal of the sub fences R and L are convenient for cutting wide and thin workpiece.
When cutting a workpiece up to 20 mm thick and more than 180 mm wide, remove the sub
fences R and L by removing the screw shown in the figure.
When cutting a workpiece over 20 mm thick, install the sub fences R and L securely with a
screw.
Refer to the table below for the relation between the size of workpiece and use/unuse of sub
fences R and L. (Fig. 53)
Workpiece size (H x W)
1
65mm x 155mm
2
20mm x 200mm
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0760 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0760 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0760

Powerplus POWX0760 User Manual - German - 27 pages

Powerplus POWX0760 User Manual - Dutch - 26 pages

Powerplus POWX0760 User Manual - French - 26 pages

Powerplus POWX0760 Additional guide - All languages - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info