677891
17
Zoom out
Zoom in
Previous page
1/23
Next page
POWX0760 EN
Copyright © 2014 VARO NV P a g e | 17 www.varo.com
10 OPERATION
CAUTION:
Before use, be sure to release the handle from the lowered position by pulling the stopper
pin and turning it to the angle of 90°.
Make sure the blade is not contacting the workpiece, etc. before the switch is turned on.
10.1 Cutting as mitre saw
WARNING: Make sure that the lower blade guard C is installed before using
in Mitre saw mode.
CAUTION:
Do not apply excessive pressure on the handle when cutting. Too much force may result
in overload of the motor and/or decreased cutting efficiency. Push down handle with only
as much force as is necessary for smooth cutting and without significant decrease in blade
speed.
Gently press down the handle to perform the cut. If the handle is pressed down with force
or if lateral force is applied, the blade will vibrate and leave a mark (saw mark) in the
workpiece and the precision of the cut will be impaired.
10.1.1 Press cutting
Secure the workpiece against guide fence and turn table. Switch on the tool without the blade
making any contact and wait until the blade attains full speed before lowering. Then gently
lower the handle to the fully lowered position to cut the workpiece. When the cut is completed,
switch off the tool and WAIT UNTIL THE BLADE HAS COME TO A COMPLETE STOP before
returning the blade to its fully elevated position.
10.1.2 Mitre cutting
Refer to the previously covered “Adjusting the Mitre angle”.
10.1.3 Bevel cut
Loosen the lever and tilt the saw blade to set the bevel angle (Refer to the previously covered
“Adjusting the bevel angle”). Be sure to retighten the lever firmly to secure the selected bevel
angle safely. Secure the workpiece against guide fence and turn table. Switch on the tool
without the blade making any contact and wait until the blade attains full speed. Then gently
lower the handle to the fully lowered position while applying pressure in parallel with the blade.
When the cut is completed, switch off the tool and WAIT UNTIL THE BLADE HAS COME TO
A COMPLETE STOP before returning the blade to its fully elevated position.
CAUTION:
Always be sure that the blade will move down to bevel direction during a bevel cut. Keep
hands out of path of saw blade.
During a bevel cut, it may create a condition whereby the piece cut off will come to rest
against the side of the blade. If the blade is raised while the blade is still rotating, this
piece may be caught by the blade, causing fragments to be scattered which is dangerous.
The blade should be raised ONLY after the blade has come to a complete stop.
When pressing the handle down, apply pressure parallel to the blade. If the pressure is not
parallel to the blade during a cut, the angle of the blade might be shifted and the precision
of the cut will be impaired.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0760 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0760 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0760

Powerplus POWX0760 User Manual - German - 27 pages

Powerplus POWX0760 User Manual - Dutch - 26 pages

Powerplus POWX0760 User Manual - French - 26 pages

Powerplus POWX0760 Additional guide - All languages - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info