677891

Powerplus POWX0760 Manual

18
Zoom out
Zoom in
Previous page
1/23
Next page
POWX0760 EN
Copyright © 2014 VARO NV P a g e | 18 www.varo.com
10.1.4 Compound cutting
Compound cutting is the process in which a bevel angle is made at the same time in which a
Mitre angle is being cut on a workpiece. Compound cutting can be performed at angle shown
in the table.
Bevel angle
Miter angle
45°
Left and Right 0 – 45°
When performing compound cutting, refer to “Press cutting”, “Mitre cutting” and “Bevel cut”
explanations.
10.1.5 Cutting aluminum extrusion (Fig. 56)
When securing aluminum extrusions, use spacer blocks or pieces of scrap as shown in the
figure to prevent deformation of the aluminum. Use a cutting lubricant when cutting the
aluminum extrusion to prevent buildup of the aluminum material on the blade.
CAUTION:
Never attempt to cut thick or round aluminum extrusions. Thick aluminum extrusions may
come loose during operation and round aluminum extrusions cannot be secured firmly
with this tool.
Never cut aluminum in the table saw mode (bench mode).
10.2 Cutting as table saw (bench mode)
CAUTION:
Always use “work helpers” such as push sticks and push blocks when there is a danger
that your hands or fingers will come close to the blade.
Always hold the workpiece firmly with the table and the rip fence. Do not bend or twist it
while feeding. If the workpiece is bent or twisted, dangerous kickbacks may occur.
NEVER withdraw the workpiece while the blade is running. If you must withdraw the
workpiece before completing a cut, first switch the tool off while holding the workpiece
firmly. Wait until the blade has come to a complete stop before withdrawing the workpiece.
Failure to do so may cause dangerous kickbacks.
NEVER remove cut-off material while the blade is running.
NEVER place your hands or fingers in the path of the saw blade.
Always secure the rip fence firmly, or dangerous kickbacks may occur.
Always use “work helpers” such as push sticks and push blocks when cutting small or
narrow workpieces, or when the ado head is hidden from view while cutting.
10.2.1 Work helpers
Push sticks, push blocks or auxiliary fence are types of “work helpers”. Use them to make safe,
sure cuts without the need for the operator to contact the blade with any part of the body.
10.2.2 Push block (Fig. 57)
Use a 19 mm piece of plywood. Handle should be in center of plywood piece. Fasten with glue
and wood screws as shown. Small piece 9.5 mm x 8 mm x 50 mm of wood must always be
glued to plywood to keep the blade from dulling if the operator cuts into push block by mistake.
(Never use nails in push block.)
10.2.3 Auxiliary fence (Fig. 58)
Make auxiliary fence from 9.5 mm and 19 mm plywood pieces.
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0760 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0760 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0760

Powerplus POWX0760 User Manual - German - 27 pages

Powerplus POWX0760 User Manual - Dutch - 26 pages

Powerplus POWX0760 User Manual - French - 26 pages

Powerplus POWX0760 Additional guide - All languages - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info