677891
14
Zoom out
Zoom in
Previous page
1/23
Next page
POWX0760 EN
Copyright © 2014 VARO NV P a g e | 14 www.varo.com
Be sure to adjust the rip fence so that it is parallel with the blade, or a dangerous kickback
condition may occur.
Be sure to adjust the rip fence so that it does not contact the top blade guard or saw
blade. (Fig. 34)
Do not relocate or carry the tool by rip fence.
Raising the installed rip fence or exerting a force on it to the right and left with your hand
grabbing its top end may damage it and impair its function.
9.6 Installing and adjusting Mitre gauge (Fig. 35)
Install the Mitre gauge by inserting its shaft into one of two grooves in the table from the front.
Mitre gauge fence that is also used as rip fence can be installed on the Mitre gauge according
to your work.
9.7 Dust bag (Fig 36, 37 & 38)
The use of the dust bag makes cutting operations clean and dust collection easy. To attach
the dust bag, fit it onto the dust nozzle.
When the dust bag is about half full, remove the dust bag from the tool and pull the fastener
out. Empty the dust bag of its contents, tapping it lightly so as to remove particles adhering to
the insides which might hamper further collection.
If you connect a vacuum cleaner to your saw, more efficient and cleaner operations can be
performed.
9.8 Securing workpiece
WARNING It is extremely important to always secure the workpiece
properly and tightly with the vise. Failure to do so can cause the tool to be
damaged and/or the workpiece to be destroyed. PERSONAL INJURY MAY
ALSO RESULT. Also, after a cutting operation, DO NOT raise the blade until
the blade has come to a complete stop.
Vertical vise (Fig. 40)
The vertical vise can be installed in two positions on either the left or right side of the guide
fence. Insert the vise rod into the hole in the guide fence and tighten the clamping screw to
secure the vise rod. Position the vise arm according to the thickness and shape of the
workpiece and secure the vise arm by tightening the clamping screw. If the screw to secure
the vise arm contacts the guide fence, install the clamping screw on the opposite side of vise
arm. Make sure that no part of the tool contacts the vise when lowering the handle all the way.
If some part contacts the vise, re-position the vise. Press the workpiece flat against the guide
fence and the turn table. Position the workpiece at the desired cutting position and secure it
firmly by tightening the vise knob.
CAUTION:
The workpiece must be secured firmly against the turn table and guide fence.
9.9 Setting up the tool in table saw mode
CAUTION:
Before use in the table saw mode, make sure that the turn table has been secured at 0°
Mitre angle with the clamping screw on the guide fence.
Before use in the table saw mode, make sure that the tool head has been secured with the
lever.
Before use in the table saw mode, make sure that the riving knife has been secured in
place properly.
Before use in the table saw mode, remove the lower blade guard (8)
In table saw mode, release the lower limit stopper.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0760 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0760 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0760

Powerplus POWX0760 User Manual - German - 27 pages

Powerplus POWX0760 User Manual - Dutch - 26 pages

Powerplus POWX0760 User Manual - French - 26 pages

Powerplus POWX0760 Additional guide - All languages - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info