677891
13
Zoom out
Zoom in
Previous page
1/23
Next page
POWX0760 EN
Copyright © 2014 VARO NV P a g e | 13 www.varo.com
The riving knife has been installed before shipment from the factory so that the blade and
riving knife are in a straight line after your simple set-up. Refer to the section titled
“Repositioning riving knife” for the set-up.
CAUTION:
If the blade and riving knife are not aligned properly, a dangerous pinching condition may
result during operation. Make sure the riving knife is positioned between both outer ends
of the blade teeth when viewing from the top. You could suffer serious personal injury
while using the tool without a properly aligned riving knife. If they are not aligned for any
reasons, always have an authorized service center repair it.
When adjusting the riving knife clearance from the blade teeth, always loosen the hex bolt
only after loosening the clamping nut.
9.5 Installing and adjusting rip fence (Fig. 28)
Install the rip fence on the table so that the rip fence holder engages with the guide rail.
Tighten the clamping screw (48) of the rip fence firmly clockwise.
Loosen the clamping screw (47)
Slide the rip fence and secure it so that the far end from you of the rip fence is aligned with
the point at which the front edge of saw blade just appears from top surface of the
workpiece. The purpose of this adjustment is to reduce risk of kick-back toward operator
that cut piece from the workpiece is pinched between the saw blade and rip fence and
finally pushed out toward operator. The line A varies by thickness of workpiece or the table
level. Adjust the position of the rip fence according to the thickness of the workpiece. After
adjusting the rip fence, tighten the clamping screw (47) firmly. (Fig. 29)
NOTE:
There are four patterns to position the rip fence as shown in the figure. Rip fence has two
slits on its sides, one slit with an elevated fringe nearby on the same side and the other
without it. Use the surface of rip fence with this fringe facing the workpiece only when
cutting off into a piece of a thin workpiece.
To change the rip fence pattern, remove the rip fence from the rip fence holder by
loosening the clamping screw (47) and change the facing of the rip fence to the rip fence
holder so that the rip fence faces the rip fence holder according to your work as shown in
the figure.
Insert the square nut on the rip fence holder into the back end of either slit of the rip fence
so that they fit as shown in the figure.
To change from the pattern A or B to the pattern C or D, or in adverse case, remove the
square nut and clamping screw (47) from the rip fence holder, then position the clamping
screw (47) and square nut on the opposite position of the rip fence holder compared to the
original position. Tighten the clamping screw (47) securely after inserting the square nut of
the rip fence holder into the rip fence slit.
Insert the square nut on the rip fence holder into the back end of either slit of the rip fence so
that they fit as shown in the figures. (Fig. 30 & 31)
The rip fence is factory adjusted so that it is parallel to the blade surface. Make sure that it is
parallel. To check to be sure that the rip fence is parallel with the blade, adjust the blade
height with the cutting depth adjusting knob so that the blade appears at the topmost position
from the table. Mark one of the blade teeth with a crayon. Measure the distance (A) and (B)
between the rip fence and blade. Take both measurements using the tooth marked with the
crayon. These two measurements should be identical. If the rip fence is not parallel with the
blade, proceed as follows: (Fig. 32 & 33)
(1) Turn the adjusting screw (55) counterclockwise.
(2) Shift the front edge of the rip fence slightly to right or left until it becomes parallel with the
blade.
(3) Tighten the adjusting screw on the rip fence firmly.
CAUTION:
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX0760 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0760 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0760

Powerplus POWX0760 User Manual - German - 27 pages

Powerplus POWX0760 User Manual - Dutch - 26 pages

Powerplus POWX0760 User Manual - French - 26 pages

Powerplus POWX0760 Additional guide - All languages - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info