Manual Powerplus POWX0760 (page 12 of 23) (English)

677891

Zoom out

Zoom in

1/23

POWX0760 EN

9.2 Table height two-way set up

The table height can be set up in two ways, high or low table.

WARNING: Before falling down the tool backwards, always set the tool in

the Mitre saw mode and lock the tool head in the lowest position.

9.2.1 High table set up (Fig. 18)

To set up the tool with high table, proceed as follows.

 Fall down the tool carefully BACKWARDS without fail while holding it with both hands.

 Fix the 4 legs using a bolt, wing nut and the U-shaped customized washer.

9.2.2 Low table set up (Fig. 19)

 Fold in the 4 legs. To do so :

 Fall down the tool carefully BACKWARDS without fail while holding it with both hands.

 untighten the wing nut of each leg seperatly until you can turn the leg 90° , aligned with

tabel. Then tigthen the wing nut again

 Return the tool to the upright position.

9.3 Installing or removing saw blade

CAUTION:

 Always be sure that the tool is switched off and unplugged before installing or removing

the blade.

 Use only the socket wrench provided to install or remove the blade. Failure to do so may

result in overtightening or insufficient tightening of the hex bolt. This could cause an injury.

Move up the handle in the fully raised position. Press the shaft lock to lock the spindle, use

the socket wrench to loosen the hex bolt clockwise. (Fig. 20) Raise the blade guard A with

its lifting lever while pushing the lever nearby the handle to the left. With the blade guard A

raised, remove the hex bolt, outer flange and blade. (Fig. 21) To install the blade, mount it

carefully onto the spindle, making sure that the direction of the arrow on the surface of the

blade matches the direction of the arrow on the blade case. Install the outer flange and

hex bolt, and then use the socket wrench to tighten the hex bolt (lefthanded) securely

counterclockwise while pressing the shaft lock.

NOTE: When installing a saw blade, be sure to insert it between the blade

guard (7) at first and then raise it so that the blade is finally placed in the

blade guard. (Fig. 22 & 23)

CAUTION:

 The ring 30 mm in outer diameter is factory-installed between the inner and outer flanges.

Return the lower blade guard (8) to its original position. Lower the handle to make sure

that the lower blade guards move properly. Make sure shaft lock has released spindle

before making cut.

9.4 Adjusting riving knife (fig 25,26 & 27)

There must be a clearance of about 5 – 6 mm between the riving knife and the blade teeth

when pushing riving knife toward the blade fully. Adjust the riving knife accordingly by first

loosening clamping nut by hand counterclockwise and then loosening hex bolt

counterclockwise with the hex socket wrench, and measuring the distance. After adjustment,

securely tighten the hex bolt and then the clamping nut clockwise. Always check to see that

the riving knife is secured and that the top blade guard works smoothly before cutting.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX0760 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX0760

Powerplus POWX0760 User Manual - German - 27 pages

Powerplus POWX0760 User Manual - Dutch - 26 pages

Powerplus POWX0760 User Manual - French - 26 pages

Powerplus POWX0760 Additional guide - All languages - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Powerplus POWX0760 Manual

Product: