675035
14
Zoom out
Zoom in
Previous page
1/20
Next page
POWX07582 EN
Copyright © 2017 VARO P a g e | 14 www.varo.com
Before starting to work, check that the following items are in a proper condition.
Riving knife (2)
Safety saw blade guard (14)
Saw blade guard (3)
Push block
Wear protective clothing and apply the necessary protective measures:
Dust exhauster
Ear protection
Safety goggles
Stand in the correct position for operating the machine
At the front of the saw
In front of the saw
At the left side of the sawing line
If two persons are working at the same time, then the other person must stand at a
sufficient distance from the saw.
Use following accessories, if required by the type of work you are doing:
Workpiece support for long workpieces, which would otherwise fall off the table at the end
of the sawing process.
Dust collector
Do not try to stop the turning of the saw blade, by pressing the workpiece against the side
of the saw blade. A risk of injuries can occur, if the saw blade is blocked.
10.2.6 Sawing
HAZARD! Always use a push block, if the distance D of the workpiece is
less than 120 mm (Fig. 4).
The front edge of the saw blade guard must rest on the workpiece.
If necessary, install the mitre and width guide, and make sure that the locking screw points
in the operator's direction.
Set the mitre and width guide to the desired sawing width. Check on both scales of the
upper saw blade that the mitre and width guide has been set parallel to the saw blade.
Start the saw blade by pushing the green switch (7) into the “ON” position.
Push the workpiece slowly towards the back and saw it in one single and flowing
movement.
If further sawing is not immediately required, then turn the machine off by pushing the red
switch (7) into the “OFF” position.
11 CLEANING AND MAINTENANCE
Attention! Before performing any work on the equipment, pull the power
plug.
11.1 Cleaning
Keep the ventilation slots of the machine clean to prevent overheating of the engine.
Regularly clean the machine housing with a soft cloth, preferably after each use.
Keep the ventilation slots free from dust and dirt.
If the dirt does not come off use a soft cloth moistened with soapy water.
Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may
damage the plastic parts.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX07582 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX07582 in the language / languages: English as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX07582

Powerplus POWX07582 User Manual - German - 22 pages

Powerplus POWX07582 User Manual - Dutch - 22 pages

Powerplus POWX07582 User Manual - French - 21 pages

Powerplus POWX07582 Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info