675035
13
Zoom out
Zoom in
Previous page
1/20
Next page
POWX07582 EN
Copyright © 2017 VARO P a g e | 13 www.varo.com
Push on the upper half of the ON/OFF switch and push on the safety lock.
Lower the saw head carefully and completely downwards, while firmly holding onto the
handgrip. You should only apply minimum pressure while sawing, so as to prevent the
motor from slowing down.
Saw the workpiece in one single movement.
Carefully let the saw head return to its topmost starting position.
If further sawing works do not have to be carried out immediately, switch the saw OFF.
10.2 Table saw mode
10.2.1 Safety instructions for the upper saw blade guard
The upper saw blade guard (3) protects against accidental contact with the saw blade and
prevents wood splinters from flying about.
Make sure that the upper saw blade guard is always installed while working.
10.2.2 Riving knife
The riving knife (2) prevents that a workpiece is grasped by the rising teeth of the saw
blade and is thrown in the direction of the operator.
Always make sure that the riving knife is installed while working with the saw.
10.2.3 Lower saw blade guard
The lower saw blade guard (14) is designed to provide protection against accidental
contact with the saw blade.
The safety saw blade guard must always be installed, while the machine is in operation.
10.2.4 Push block
A push block (24) serves as an extension of the hand and protects against accidental
contact with the saw blade.
Always use a push block, when the interval between the saw blade and the mitre and
width guide is less than 120 mm.
Use the push block at an angle of 20° to 30° in relation to the surface of the saw table.
Replace the push block when damaged.
10.2.5 Installation
HAZARD!
Before starting with the installation of the machine:
Switch the machine “OFF
Remove the plug from the socket
Wait until at the machine has come to a complete standstill
Leave the saw head in a raised position.
Set the mitre saw in the 0° position and tighten up the locking screw.
You must position the lower saw blade guard (14) correctly and you must make sure that
switch B (29) is activated.
Lower the saw head and lock it in position.
Remove the mitre and width guide (4) from the saw blade guard (3).
HAZARD!
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX07582 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX07582 in the language / languages: English as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX07582

Powerplus POWX07582 User Manual - German - 22 pages

Powerplus POWX07582 User Manual - Dutch - 22 pages

Powerplus POWX07582 User Manual - French - 21 pages

Powerplus POWX07582 Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info