675035
12
Zoom out
Zoom in
Previous page
1/20
Next page
POWX07582 EN
Copyright © 2017 VARO P a g e | 12 www.varo.com
Lower the saw head carefully and completely downwards while holding firmly onto the
handgrip. You should only apply medium pressure while sawing, so as to prevent that the
speed of the motor slows down.
Saw the workpiece in one single movement.
Carefully let the saw head return to its topmost starting position.
The saw should be switched off by releasing the switch (20), if no further sawing has to be
done.
Note: The mitre saw is activated at certain angles, such as at 0°, 15°, 22.5°,
30°, 45° and 60°.
10.1.6 Bevelling
During bevelling, the workpiece is sawn at an angle of less than 90°.
Starting position:
Saw head completely raised.
Motor head in the 0° position; the locking screw of the turntable is tightened.
10.1.7 Sawing the workpiece:
Release the bevelling locking knob (16) for tilting the saw head close to the saw.
Tilt the motor head carefully to the desired position.
Tighten up the bevelling lock knob (16).
Hold the workpiece against the mitre and width guide. If necessary, use a work clamp for
fastening the workpiece.
Activate the switch (20) and activate/push on the safety lock (6).
Lower the saw head carefully and completely downwards, while firmly holding onto the
handgrip. You should only apply medium pressure while sawing, so as to prevent that the
speed of the motor slows down.
Saw the workpiece in one single movement.
Carefully let the saw head return to its topmost starting position.
The saw should be switched off by releasing the switch (20), if no further sawing has to be
done.
10.1.8 Double mitre cut
A double mitre cut is a combination of a mitre cut and a bevelling cut; this means that the
workpiece is cut at an angle in the one single movement, which is not equal to 90° in
relation to the mitre and width guide and the material surface.
HAZARD! The saw blade is exposed much more than normally when
making a double mitre cut, which leads to an increased risk of injuries.
Always keep sufficient distance from the saw blade.
Starting position:
Saw head completely raised.
Mitre saw locked in the desired position.
Saw head tilted at the desired angle, in relation to the surface of the workpiece, and locked
in position.
10.1.9 Sawing the workpiece:
Hold the workpiece against the mitre and width guide. If possible, use a work clamp for
fastening the workpiece.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX07582 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX07582 in the language / languages: English as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX07582

Powerplus POWX07582 User Manual - German - 22 pages

Powerplus POWX07582 User Manual - Dutch - 22 pages

Powerplus POWX07582 User Manual - French - 21 pages

Powerplus POWX07582 Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info