675035
10
Zoom out
Zoom in
Previous page
1/20
Next page
POWX07582 EN
Copyright © 2017 VARO P a g e | 10 www.varo.com
The mains voltage and the system frequency must conform to the voltage and frequency
that is indicated on the technical data sheet of the machine;
Fusing protection with a residual current device (RCD), with a sensitivity of 30 mA.
Sockets must be properly installed, earthed and tested.
Position a power cable in such a way that it does not hinder the work and cannot be
damaged.
Protect the power cable against heat, aggressive fluids and sharp edges.
Only use rubber-coated extension cables with a sufficient wire cross-section (3 x 1.5
mm²).
Do not use the power cable for pulling the plug out of the socket.
10 OPERATIONS
This saw can be used as a:
Cross-cut saw/ miter saw
Table saw
Before making any changes in the settings of this machine, always remove
the plug from the socket.
10.1 Cross-cut sawing mode
10.1.1 Safety instructions for the liftable saw blade guard (Fig. 3)
The liftable saw blade guard (C1) protects against accidental contact with the saw blade and
flying wood splinters.
The liftable saw blade guard must always return automatically to the start position, whenever
the saw head is lifted. The saw blade must be covered at all sides, when the saw head is
located in the start position.
10.1.2 Safety lock
The safety lock (6) blocks the saw head in the topmost position, and it prevents that the liftable
saw blade guard exposes the saw blade.
The safety lock is released by pushing on it. The saw head (19) can now be lowered; as the
saw head is lowered, the saw blade guard retracts and the saw blade is freed.
After a cut has been made, and when the saw head is back in the topmost starting position,
the liftable saw blade guard is once more blocked by the safety lock.
10.1.3 Installation
HAZARD!
Before starting with the installation of the machine:
Switch the machine “OFF”
Remove the plug from the socket
Wait until at the machine has come to a complete standstill
The upper saw blade guard (3) and the mitre and width guide (4) must be installed, so that
the saw blade can be covered and safely fastened. The mitre and width guide must
activate switch A (8); secure the position with the mitre guide locking knob (5).
Release the locking knob (22) and lift up the saw head completely
Remove the lower saw blade guard (14).
Use the switch (20) for activating the machine.
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Powerplus POWX07582 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Powerplus POWX07582 in the language / languages: English as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Powerplus POWX07582

Powerplus POWX07582 User Manual - German - 22 pages

Powerplus POWX07582 User Manual - Dutch - 22 pages

Powerplus POWX07582 User Manual - French - 21 pages

Powerplus POWX07582 Additional guide - All languages - 5 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info